<<

стр. 10
(всего 13)

СОДЕРЖАНИЕ

>>

CC Document sensor
CH Door open
EE Developer did not set up properly
EL Developer sensor
EU Developer sensor
H2 Thermistor
H3 High temperature
H4 Low temperature
L1 Forward scan
L2 Forward scan
L3 Scan return
L5 Lens
L6 Bottom rotating cassette
L8 Signal
L9 Sorter
U1 Battery
U2 Back up battery
U3 Auto exposure sensor
U5 Problem in interface between machine and ADF
Коды ошибок копировальных аппаратов

Sharp 781
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 7850
Code Description
CC Document sensor
CH Door open
EE Developer did not set up properly
EL Developer sensor
EU Developer sensor
H2 Thermistor
H3 High temperature
H4 Low temperature
L1 Forward scan
L2 Forward scan
L3 Scan return
L5 Lens
L6 Bottom rotating cassette
L8 Signal
L9 Sorter
U1 Battery
U2 Back up battery
U3 Auto exposure sensor
U5 Problem in interface between machine and ADF
Коды ошибок копировальных аппаратов

Sharp 7900
Code Description
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 810
Code Description
1 Open interlock switch
2 Bad thermofuse/thermistor
3 High or low temperature
4 Scanner problem
0 Data transfer
10 Mirror base
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 8100
Code Description
0 Data transfer
10 Mirror base
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 811
Code Description
1 Door or separator interlock
2 Instantly=Thermofuse
3 High temperature
4 Low temperature (if it takes 11 min)
5 Scanner problem if it takes several seconds
6 Optics problem on 820
7 Thermistor
Коды ошибок копировальных аппаратов

Sharp 815
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 816
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 820
Code Description
1 Door or separator interlock
2 Instantly=Thermofuse
3 High temperature
4 Low temperature (if it takes 11 min)
5 Scanner problem if it takes several seconds
6 Optics problem on 820
7 Thermistor
A1 Document feeder problem.
CH Toner cartridge not installed or not installed properly.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
L1 Document feeder problem.
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Sub code 2: Lens drive, motor, sensor
P Paper feed.
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5 Sub code 5: high temperature at exposing glass when using document feeder.
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 8200
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 825
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
A1 Document feeder problem.
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
CH Toner cartridge not installed or not installed properly.
H1 Heater thermal fuse
H2 Sub code 0: Fuser thermistor.
H2 Thermistor
H3 High Temperature
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Document feeder problem.
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 PT/main motor
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Lens
L5 Sub code 2: Lens drive, motor, sensor
L6 Charge block switch
P Paper feed.
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U3 Dark box
U5 Sub code 5: high temperature at exposing glass when using document feeder.
Коды ошибок копировальных аппаратов

Sharp 826
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
0 Data transfer
10 Mirror base
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 8260
Code Description
0 Data transfer
10 Mirror base
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 830
Code Description
A1 Document feeder problem.
CH Toner cartridge not installed or not installed properly.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
L1 Document feeder problem.
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Sub code 2: Lens drive, motor, sensor
P Paper feed.
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5 Sub code 5: high temperature at exposing glass when using document feeder.
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 8300
Code Description
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 835
Code Description
A1 Document feeder problem.
CH Toner cartridge not installed or not installed properly.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
L1 Document feeder problem.
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Sub code 2: Lens drive, motor, sensor
P Paper feed.
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5 Sub code 5: high temperature at exposing glass when using document feeder.
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 8350
Code Description
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 8400
Code Description
CC Not sensing document on glass
CH Door open/DV unit not installed properly
EE DV did not set up properly
EL DV problem-overtoned condition
EU DV problem-undertoned condition
H2 Fuser thermistor
H3 Fuser temperature too high
H4 Fuser temperature too low
L1 Forward scan
L3 Return scan
L7 Developer unit shift problem
PC Key counter
U1 Dead battery
U2 Battery problem
Коды ошибок копировальных аппаратов

Sharp 845
Code Description
A1 Document feeder problem.
CH Toner cartridge not installed or not installed properly.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
L1 Document feeder problem.
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Sub code 2: Lens drive, motor, sensor
P Paper feed.
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5 Sub code 5: high temperature at exposing glass when using document feeder.
Коды ошибок копировальных аппаратов

Sharp 850
Code Description
1 Door or separator interlock
2 Instantly=Thermofuse
3 High temperature
4 Low temperature (if it takes 11 min)
5 Scanner problem if it takes several seconds
6 Optics problem on 820
7 Thermistor
Коды ошибок копировальных аппаратов

Sharp 8600
Code Description
0 Data transfer
10 Mirror base
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 8875
Code Description
C2 Transfer corona problem
If lit steadily, open door or other interlock. If flashing, developer unit not installed or not connected
CH
properly
H2 Fuser thermistor
H3 Fuser overheat. Triac pinched wire
H4 Low fuser temperature. Lamp, thermal fuse, thermistor, connection
L1 Scan problem. Did not leave home position
L2 Scan left home, but did not complete scan
L3 No return scan
L4 Drive problem
L5 Lens problem
Sorter index. If 0 is flashing, sorter index home sensor did not actuate. If 1 is flashing, sorter bottom
L9
actuator remained actuated
U1 Battery. Replace battery (might have 2) and do simulation 13 to reset
U2 Communication problem within boards. To reset, jumper test points W2 & U2
Коды ошибок копировальных аппаратов

Sharp 900
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 901
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 9300
Code Description
0 Desk board and main board
0 Data transfer
10 Desk alignment board
10 Mirror base
20 Sort gate
4 Stepping motor clock pulse
40 Lens
8 Mirror motor
U3 Press {Print} and read secondary code:
U4 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 9500
Code Description
0 Data transfer (duplex tray board and main board)
0 Data transfer
1 Alignment plate not home
10 Mirror not home
2 Inversion motor
20 Mirror base collision sensor
3 24V problem
4 Stepping motor
40 Lens not home
8 Mirror motor
U3 Press Print
U4 Duplex;press {Print}
Коды ошибок копировальных аппаратов

Sharp 9550
Code Description
0 Data transfer (duplex tray board and main board)
0 Data transfer
1 Alignment plate not home
10 Mirror not home
2 Inversion motor
20 Mirror base collision sensor
3 24V problem
4 Stepping motor
40 Lens not home
8 Mirror motor
U3 Press Print
U4 Duplex;press {Print}
Коды ошибок копировальных аппаратов

Sharp 9700
Code Description
40(flashing) Lens home problem
C2 Transfer corona
CH Door open
CH(flashing) DV unit not installed
CL Drum cleaner connector
H2 Thermistor
H3 High fuser temperature
H4 Low fuser temperature
L1 Mirror
L2 Scan
L3 Scan return
L4 Drive
L5 Lens
PC Key counter
U1 Dead battery
U2 Dead battery
U3 Lens or mirror
U4 Duplex
Коды ошибок копировальных аппаратов

Sharp 9750
Code Description
40(flashing) Lens home problem
C2 Transfer corona
CH Door open
CH(flashing) DV unit not installed
CL Drum cleaner connector
H2 Thermistor
H3 High fuser temperature
H4 Low fuser temperature
L1 Mirror
L2 Scan
L3 Scan return
L4 Drive
L5 Lens
PC Key counter
U1 Dead battery
U2 Dead battery
U3 Lens or mirror
U4 Duplex
Коды ошибок копировальных аппаратов

Sharp ALL
Code Description
0 Main motor/main PWB data transfer
10 Mirror motor
4 Stepping motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermofuse
CH
DV unit is not in
(flickering)
H1 Heat thermofuse
H2 Thermistor
H3 High temperature
H4 Low temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward scan
L2 End of scan
L3 Return scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermofuse
U1 Low battery
U2 Data transfer
U3 Dark box
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CE Sorterdoor
CH Interlock or optics thermofuse
CH
DV unit out
(flashing)
L1 Scan forward
L2 Scan
L3 Scan not at home
L4 Main motor not turning (PT)
L5 Lens
L6 Charge blockswitch (781)
L8 No power to main board
L9 Sorter
Коды ошибок копировальных аппаратов

Sharp SF-2014
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp SF2314
Code Description
If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing,
CH
developer seal still installed, or toner density sensor/main board problem.
Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub
EE
code EL: Over toned. May be toner density sensor problem or developer unit problem.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L1 leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came
off.
L3 Scan return problem. Sub code 0. Approximately same causes as L1
L4 Sub code 1: Main drive problem. Sensor, gear, motor.
L5 Sub code 2: Lens drive, motor, sensor.
Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE
L8
sensor problem.
PC Key counter not installed.
SPFJAM Document feeder problem.
U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.
U5 Sub code 5: high temperature at exposure glass when using document feeder.
Коды ошибок копировальных аппаратов

Sharp SN-1420
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp Z50
Code Description
(Z70)E Magnification dial not set properly
H Heater problem (fuser has resettable
L Scan problem
P Paper feed problem
Коды ошибок копировальных аппаратов

Sharp Z55
Code Description
(Z70)E Magnification dial not set properly
H Heater problem (fuser has resettable
L Scan problem
P Paper feed problem
Коды ошибок копировальных аппаратов

Sharp Z60
Code Description
F Thermal fuse
L Scan problem
U Low battery
Коды ошибок копировальных аппаратов

Sharp Z-60
Code Description
F Thermal fuse - exposure or fuser
H Heater problem
H Heater problem
L Scan problem
U Low Battery
Коды ошибок копировальных аппаратов

Sharp Z70
Code Description
(Z70)E Magnification dial not set properly
H Heater problem (fuser has resettable
L Scan problem
P Paper feed problem
Коды ошибок копировальных аппаратов

Sharp Z-800
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp Z810
Code Description
A1 Document feeder problem.
CH Toner cartridge not installed or not installed properly.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
L1 Document feeder problem.
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L3
leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4 Sub code 1: Main drive problem. Sensor gear motor.
L5 Sub code 2: Lens drive, motor, sensor
P Paper feed.
U2 Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5 Sub code 5: high temperature at exposing glass when using document feeder.
Коды ошибок копировальных аппаратов

Toshiba 3570
Toshiba 3810
Toshiba 3910
Toshiba 4010
Toshiba 4111
Toshiba 4121
Toshiba 1340
Toshiba 4560
Toshiba 1350
Toshiba 4570
Toshiba 1550
Toshiba 4810
Toshiba 1650
Toshiba 4910
Toshiba 1710
Toshiba 5010
Toshiba 2050
Toshiba 5020
Toshiba 2060
Toshiba 5120
Toshiba 2310
Toshiba 5510
Toshiba 2500
Toshiba 5511
Toshiba 2510
Toshiba 5610
Toshiba 2532
Toshiba 5620
Toshiba 2540
Toshiba 727
Toshiba 2810
Toshiba 728
Toshiba 2860
Toshiba 7610
Toshiba 2870
Toshiba 7720
Toshiba 3210
Toshiba 7812
Toshiba 3220
Toshiba 7815
Toshiba 3550
Toshiba 7816
Toshiba 3560
Toshiba 7910
Toshiba 8412
Toshiba 8510
Toshiba 8812
Toshiba 9110
Toshiba 9230
Коды ошибок копировальных аппаратов

Toshiba 1340
Code Description
C5 Scan problem
C6 Scan problem
C7 Fuser problem (reset with 0 & 5 mode, code 89)
CE Missing EEPROM
CF Board problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E5 Paper feed jam
EO Toner waste bottle is full
Коды ошибок копировальных аппаратов

Toshiba 1350
Code Description
C5 Scan problem
C6 Scan problem
C7 Fuser problem (reset with 0 & 5 mode, code 89)
CE Missing EEPROM
CF Board problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E5 Paper feed jam
EO Toner waste bottle is full
Коды ошибок копировальных аппаратов

Toshiba 1550
Code Description
C01 Main motor drive problem
C21 Optics problem Scan , lens, mirror.
C26 Exposure lamp detect problem.
C32 Setup error (UA)
C41 Fuser thermistor, or no heat.
C43 Fuser thermistor problem or other fuser problem, after machine goes into ready.
C44 Heater problem
C54 Communication problem between sorter and machine main board.
C55 Communication problem between ADF and machine main board.
C71 ADF drive problem.
C72 ADF registration sensor problem.
C73 EEPROM initialization problem.
C81 Sorter paper conveying motor.
C82 Sorter bin motor.
C83 Sorter upper sensor.
C84 Sorter lower sensor.
C85 Sorter home sensor.
C86 Sorter copy removal sensor.
C94 Optics initialization problem in test modes.
E01 Paper jam
E02 Fuser jam
E03 Paper jam
E05 Paper feed ham
E14 lower cassette jam
E71 ADF jam
E72 ADF jam
E73 ADF jam
E75 ADF jam of 2nd original
E81 Sorter jam
E82 Sorter jam
Коды ошибок копировальных аппаратов

Toshiba 1650
Code Description
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU’s
C5 Scan or optic problem. Locked up or won’t initialize or return to home position
C7 Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam
Коды ошибок копировальных аппаратов

Toshiba 1710
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
AO Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won’t shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam
Коды ошибок копировальных аппаратов

Toshiba 2050
Code Description
A4 Sorter problem
A5 Communication problem between main CPU and IPC
A6 Sorter interface problem
C2 Communication problem between CPU’s
C5 Scan or optic problem. Locked up or won’t initialize or return to home position
C7 Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF Developer calibration problem
CF Developer calibration problem
CP Drive problem
E1 Paper jam
E2 Fuser jam
E3 Paper jam
E4 Front door opened during copy cycle
E5 Paper feed jam
Коды ошибок копировальных аппаратов

Toshiba 2060
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem.
C11 Duplex exit motor.
C12 Duplex end motor.
C13 Upper cassette.
C14 Lower cassette.
C15 Pedestal upper cassette.
C16 Pedestal middle cassette.
C17 Pedestal lower cassette.
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona.
C41 Fuser thermistor or low temperature.
C43 Fuser problem after warm-up.
C44 Fuser problem after warm-up.
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys
C45 while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the
display. Using the # keys, press "0" & "9" at the same time.
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter
Коды ошибок копировальных аппаратов

Toshiba 2310
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
AO Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won’t shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam
Коды ошибок копировальных аппаратов

Toshiba 2500
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
AO Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won’t shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam
Коды ошибок копировальных аппаратов

Toshiba 2510
Code Description
A1 Charge corona cleaner problem
A2 ADD problem
A4 Sorter problem
A5 Board problem
A6 Sorter board problem
A7 ADF interface
AO Communication problem between main board and PFC
C1 Board problem
C2 Board problem
C3 Board problem
C4 Board problem
C5 Optics locked or not initialized. Could be scan or lens/mirror
C7 Fuser thermistoe problem, or low temperature
C8 Scan motor won’t shut off
CA Main board problem
CB ADF drive problem
CC ADF drive problem
CD BC RAM hardware
CE BC RAM software
CP Drive problem
E0 Waste toner full
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy run
E5 Feed jam
E8 Jam in ADD (duplex)
E9 Jam in pedestal
EC ADF jam
ED ADF jam
EE ADF exit/reverse jam
Коды ошибок копировальных аппаратов

Toshiba 2532
Code Description
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won’t initialize or won’t move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC ADF belt motor or exit motor not turning
CF Auto toner adjustment did not take
CP Drive problem in machine
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy cycle
E5 Feed jam
Коды ошибок копировальных аппаратов

Toshiba 2540
Code Description
A4 Sorter problem
A5 Communication problem with main board
A6 Communication problem with sorter
A7 Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2 Communication problem between main board
C5 Scan won’t initialize or won’t move
C7 Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC ADF belt motor or exit motor not turning
CF Auto toner adjustment did not take
CP Drive problem in machine
E1 Jam
E2 Fuser jam
E3 Jam
E4 Front door was opened during copy cycle
E5 Feed jam
Коды ошибок копировальных аппаратов

Toshiba 2810
Code Description
C1 Scan did not return home
C3 Scan home sensor
C4 Scan problem
C5 Scan limit sensor
C6 Scan did not return
C7 Thermistor or other fuser problem
CC Scan did not leave home
CP Drive
E1 Jam inside machine
E2 Fuser jam or exit jam
E3 Exit switch or registration switch
E5 Paper feed jam
E7 Cassette or registration jam
Коды ошибок копировальных аппаратов

Toshiba 2860
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem.
C11 Duplex exit motor.
C12 Duplex end motor.
C13 Upper cassette.
C14 Lower cassette.
C15 Pedestal upper cassette.
C16 Pedestal middle cassette.
C17 Pedestal lower cassette.
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona.
C41 Fuser thermistor or low temperature.
C43 Fuser problem after warm-up.
C44 Fuser problem after warm-up.
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys
C45 while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the
display. Using the # keys, press "0" & "9" at the same time.
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam
E11 Duplex jam
E12 Bypass jam
E13 Upper cassette jam
E14 2nd cassette jam
E15 3rd cassette jam
E16 4th cassette jam
E17 4th cassette jam
E19 CT jam
E21 LCT jam
E22-E25 Paper jams in copier
E71 ADF feed jam
E72 ADF transport jam
E73 ADF exit jam
E74 RADF jam
E75 ADF 2nd original jam
E81-E85 Sorter jam
E88 Jam after sorter
Коды ошибок копировальных аппаратов

Toshiba 2870
Code Description
C01 Main motor drive problem
C04 Pedestal main drive problem
C05 Duplex drive problem.
C11 Duplex exit motor.
C12 Duplex end motor.
C13 Upper cassette.
C14 Lower cassette.
C15 Pedestal upper cassette.
C16 Pedestal middle cassette.
C17 Pedestal lower cassette.
C18 LCT
C21 Scan problem
C22 Lens problem
C23 Mirror motor
C26 Exposure lamp
C27 Scan motor
C33 Set up failure
C35 Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona.
C41 Fuser thermistor or low temperature.
C43 Fuser problem after warm-up.
C44 Fuser problem after warm-up.
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys
C45 while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the
display. Using the # keys, press "0" & "9" at the same time.
E01 Jam
E02 Fuser jam
E03 Jam at turn on
E04 Front door opened during copy cycle
E05 Registration jam
E08 Duplex unit jam

<<

стр. 10
(всего 13)

СОДЕРЖАНИЕ

>>