<<

стр. 2
(всего 13)

СОДЕРЖАНИЕ

>>

E520 Finisher
E530 Finisher
E530 Finisher; guide plate motor, stapler guide, finisher board
E531 Finisher
E531 Finisher; staple motor, staple sensor, finisher board.
EOO1 High fuser temperature
EOOO Low fuser temperature
Коды ошибок копировальных аппаратов

Canon 8530
Code Description
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90
sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150 C
E000 within 8 min after power -on. The surface temperature of the fixing assembly upper roller fails to
reach 180 C within 5 min after it has reached 150 C. The surface temperature of the fixing assembly
upper roller falls below 50 C in standby.
E001 The surface temperature of the fixing assembly upper roller exceeds 250 C.
E005 The cleaning belt inside the fixing assembly has been taken up more than a specified length.
E010 After generation of the main motor drive signal, two or more pulses are not received within 2 sec.
The accumulative time during which the toner supply signal (TSP) has been generated by the
E020
developing assembly reaches 3 min.
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray
E050 motor drive signal (TMDP1,2) is being generated. The holding tray home position signal (THP) is
generated 1 sec or more while the holding tray motor drive signal (TMDP1.2) is being generated.
E13 The error detection circuit on the waste toner feed motor driver PCB has detected on overcurrent.
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is
E203
generated.
The lens home position signal (LHP) is not generated within 4.8 sec after the power switch or door
E210
switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more.
E240 An error has occurred in the microprocessor on the DC controller PCB.
An error has occurred in the communication between the microprocessor of the DC controller PCB
E243
and the microprocessor in the control panel.
An error has occurred in the communication between the DC controller PCB and the controller PCB
E710
of the option, and the DC controller has detected the error.
Коды ошибок копировальных аппаратов

Canon 8570
Code Description
E000 Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etc
E001 Fuser problem. Temperature too high. Probably triac
E005 Fuser web finished
E005 Fuser cleaner belt user up
E010 Drive
E010 Main drive problem
E011 Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor
Main motor, scan motor, cleaner belt motor, duplex motor, toner motor, lens motor or driver bd. for
E011
any of these
E020 Toner sensor problem or lack of toner feed. This occurs if toner feed signal is present for 3 min
E020 Toner empty sensor sees no toner added for 3 min probably toner feed problem
E050 Duplex problem
E050 Duplex problem
E203 Scan motor problem
E203 Scan motor
E210 Lens motor problem
E210 Lens home sensor or lens won’t leave home
E240 DC controller board
E240,
E241, Control board (main board)
E242
E241 DC controller board
E242 DC controller board
E243 Operation panel board
E243 Operation panel
E400 DC controller, ADF board or 24V
E400 DC controller or document feed board
E500 DC controller or sorter board
E500 DC controller, sorter board or 24V
E510 Finisher; feed motor, pulse sensor, finisher board
E510 Finisher
E520 Finisher; stack motor, stack tray sensor, finisher board
E520 Finisher
E530 Finisher
E530 Finisher; guide plate motor, stapler guide, finisher board
E531 Finisher
E531 Finisher; staple motor, staple sensor, finisher board.
EOO1 High fuser temperature
EOOO Low fuser temperature
Коды ошибок копировальных аппаратов

Canon 8580
Code Description
The temperature of the upper fixing roller has not increased above the specified level 90 seconds
after switching power on. The temperature of the upper fixing roller does not reach 150 C within 8
E000 minutes after switching power ON. The temperature of the upper fixing roller does not reach 180 C
within 5 minutes of reaching 150 C. The temperature of the upper fixing roller drops below 50 C
during STANDBY.
E001 The temperature of the upper fixing roller exceeds 250 C.
E005 The length of fixing assembly cleaning belt wound on the take-up reel exceeds the specified length.
When two or more clock pulses are not inputted for a period of 2 seconds after a MAIN MOTOR
E010
DRIVE command is generated.
When excessive current is detected by the fault detection circuit of the DC driver PCB. When
E011 excessive current is detected by the fault detection circuit of the duplexing unit driver PCB. When
excessive current is detected by the fault detection circuit of the scanner motor driver PCB.
When a toner out signal (TSP) is emitted from the developing assembly for a total of at least two
E020
minutes.
When the HOLDING TRAY HOME POSITION signal (THP) is not generated within 4 seconds from
the beginning of HOLDING TRAY MOTOR DRIVE command (TMDP1,2) When the HOLDING TRAY
E050
HOME POSITION signal (THP) is generated for at least one second while the HOLDING TRAY
MOTOR DRIVE command (TMDSP1,2) is being generated.
When two or more clock pulses are not inputted from the SCANNER MOTOR DRIVE command is
E203
being generated.
When the LENS HOME POSITION signal (LHP) is not generated within 4.8 seconds after the power
E210 switch or door switch goes ON. When the LENS HOME POSITION signal (LHP) is generated for 2
seconds or more.
When an abnormally in communication occurs between the microprocessors on the DC controller
E243
PCB and those on the control panel PCB.
When an abnormality in communication occurs between the DC controller PCB detect RDF controller
E400
PCB.
When a flag mounted on the pick-up roller HOME position sensor (S3), it indicates that M1 is turning.
E401
S3 should go ON and OFF two or more times in one second.
E402 The number of pulses in a 200 ms period is too low.
E403 When the number of feed motor clock pulses in a 200 ms period is less than the correct value.
E411 When the sensor output is greater than 2.3V when there is paper.
When an abnormality in communication occurs between the DC controller PCB of sorter detect main
E500
controller PCB.
E510 When there is no pulse output from the feed roller motor and when the first copy jams.
The lead can HOME position sensor does not go "OFF" within 0.5 second after the BIN MOTOR
E540
DRIVE signal (BMON) is output.
The lead can HOME position sensor does not go "ON" within 1.0 second after the lead cam position
E541
sensor goes "OFF".
When an abnormality in communication occurs between the DC controller PCB and the RF controller
E710
PCB or sorter controller PCB detect DC controller PCB.
Коды ошибок копировальных аппаратов

Canon 9800
Code Description
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90
E000 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150 C
within 8 min after power-on.
E001 The surface temperature of the fixing assembly upper roller exceeds 250 C.
E005 The cleaning belt inside the fixing assembly has been taken up more than a specified length.
E010 After generation of the main motor drive signal, two or more pulses are not received within 2 sec.
E013 The error detection circuit on the waste toner feed motor driver PCB has detected an overcurrent.
The accumulative time during which the toner supply signal (TSP) has been generated by the
E020
developing assembly reaches 3 min*.
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray
E050 motor drive signal (TMDP1, 2) is being generated. The holding tray home position signal (THP) is
generated 1 sec or more while the holding tray motor drive signal (TMDP1, 2) is being generated.
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is
E203
generated.
The lens home position signal (LHP) is not generated within 4.8 sec after power switch or door switch
E210
has gone ON. The lens home position signal (LHP) is generate 2 sec or more.
E240 An error has occurred in the microprocessor on the DC controller PCB.
An error has occurred in the microprocessor of the DC controller PCB and the microprocessor in the
E243
control panel.
An error has occurred in the communication between the DC controller PCB and the controller PCB
E710
of the option, and the DC controller has detected the error.
No communication is perceived from the RF controller PCB for 200 ms or more the communication is
E712
monitored at all times.
Коды ошибок копировальных аппаратов

Canon A-1,B1
Code Description
E500 An error is identified in the communication between the sorter and copier.
E510 The clock signal from the motor is absent for 250 ms or more.
E513 The clock signal from the motor is absent for 250 ms or more.
The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drive
E530
command has been generated.
The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command has
E531
been generated. MS9 fails to go back OFF within 1000 ms after it has gone ON.
The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drive
E540
command has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF.
Коды ошибок копировальных аппаратов

Canon C-120
Code Description
C No problem. Means that the machine is correcting the fuser film tracking.
Drum must be changed. Could be the drum serial number is identified by the logic as being
CC
non-compatible to that particular copier.
E000 Low fuser temperature
E001 High fuser temperature
E002 High fuser temperature
E003 Erratic fuser temperature
E007 Fuser film off track and will not repair itself
E010 Main drive problem
E030 Counter problem
E064 Scan problem, or power supply
E202 Scan problem
E210 Lens drive problem or lens sensor
E220 Exposure lamp stays on or off
E240 DC controller (main board) or composite power supply
E261 Zero cross problem. Power frequency or composite power supply
E400 Communication problem between boards
E803 24 volt problem
EO Fuser problem
H Fuser overheat
Коды ошибок копировальных аппаратов

Canon C-160
Code Description
E000 Fuser thermistor, heater, thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly
E010 Main motor drive problem
E030 Counter
E064 Composite power supply or main board
E202 Scan problem
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply
E261 Composite power supply or fluctuating power
E400 ADF communication problem to machine
E402 ADF belt motor drive
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem
E510 Sorter drive problem
E530 Stapler guide bar motor
E531 Stapler swing motor
E540 Bin shift motor
E541 Bin motor drive problem
E710 Main board
E711 Main board
E712 Main board or communication problem with ADF
E717 Main board, asst. board
U0 Initializing. Sets all user modes to factory default settings
U1 Auto clear timer. Range 1-9. Each digit=1 minute
U2 Automatic power shut off timer
U3 Fine adjustment of zoom
U4 Auto cassette switching
U5 Sort or non-sort default
U6 Cleans document feeder pickup assembly
U7 CLEAR "replace drum"
U9 Auto exposure or manual exposure as default
Коды ошибок копировальных аппаратов

Canon C-180
Code Description
E000 Fuser problem. Low temperature. Lamp, thermal switch, AC driver
E001 Fuser problem. High temperature. Triac, AC driver, pinched wire
E004 Fuser problem
E0053 Sorter
E030 Counter
E202 Scan
E210 Lens
E221 Exposure lamp regulator board, thermal fuse, exposure lamp
E400 Automatic document feeder
E500 Sorter
E710 DC controller
Коды ошибок копировальных аппаратов

Canon C200D
Code Description
E000 Fuser thermistor, heater thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac.
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407
E010 Main motor drive problem
E030 Counter
E041 Paper deck motor, clutch or sensor
E064 Composite power supply or main motor board
E202 Scan problem. Motor sensor.
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply.
E260 Main board, power supply cooling fan or composite power supply.
E261 Composite power supply or fluctuating power.
E400 ADF communication to machine.
E401 ADF pickup motor or sensor.
E402 ADF belt motor drive
E403 ADF feed motor or slip sensor.
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem.
E510 Sorter drive problem.
E530 Stapler guide bar motor.
E531 Stapler swing motor.
E540 Bin shift motor.
E541 Bin motor drive problem.
E710 Main board (DC controller.)
E711 Main board (DC controller.)
E712 Main board or communication problem with ADF, or ADF main board.
Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.
E717
Reset with user
E802 Composite power supply or DC controller.
E901 Cassette feed unit board or cassette feed motor.
E902 Horizontal registration problem. I think this refers to the duplex section.
J1 Feed jam
J10 Duplex exit jam
J11 Vertical jam
J12 Vertical jam
J13 Vertical jam
J14 Vertical jam
J15 Deck jam
J2 Feed jam
J3 Separation area jam
J4 Separation area jam
J5 Exit jam
J6 Exit jam
J7 Sorter jam
J8 Door open jam
J9 Cassette jam
JA Cassette jam
Jb Cassette jam
JC Cassette jam
Jd Duplex feed jam
JE Duplex exit jam
JF Duplex registration jam
Коды ошибок копировальных аппаратов

Canon NP 1820/6012/6016/6025/6060
Code Description
E000 Fuser problem. Low temperature. Lamp, thermal switch, AC driver
E001 Fuser problem. High temperature. Triac, AC driver, pinched wire
E004 Fuser problem
E0053 Sorter
E030 Counter
E202 Scan
E210 Lens
E221 Exposure lamp regulator board, thermal fuse, exposure lamp
E400 Automatic document feeder
E500 Sorter
E710 DC controller
C No problem. Means that the machine is correcting the fuser film tracking.
Drum must be changed. Could be the drum serial number is identified by the logic as being
CC
non-compatible to that particular copier.
E000 Low fuser temperature
E001 High fuser temperature
E002 High fuser temperature
E003 Erratic fuser temperature
E007 Fuser film off track and will not repair itself
E010 Main drive problem
E030 Counter problem
E064 Scan problem, or power supply
E202 Scan problem
E210 Lens drive problem or lens sensor
E220 Exposure lamp stays on or off
E240 DC controller (main board) or composite power supply
E261 Zero cross problem. Power frequency or composite power supply
E400 Communication problem between boards
E803 24 volt problem
EO Fuser problem
H Fuser overheat
E000 Fuser thermistor, heater, thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly
E010 Main motor drive problem
E030 Counter
E064 Composite power supply or main board
E202 Scan problem
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply
E261 Composite power supply or fluctuating power
E400 ADF communication problem to machine
E402 ADF belt motor drive
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem
E510 Sorter drive problem
E530 Stapler guide bar motor
E531 Stapler swing motor
E540 Bin shift motor
E541 Bin motor drive problem
E710 Main board
E711 Main board
E712 Main board or communication problem with ADF
E717 Main board, asst. board
U0 Initializing. Sets all user modes to factory default settings
U1 Auto clear timer. Range 1-9. Each digit=1 minute
U2 Automatic power shut off timer
U3 Fine adjustment of zoom
U4 Auto cassette switching
U5 Sort or non-sort default
U6 Cleans document feeder pickup assembly
U7 CLEAR "replace drum"
U9 Auto exposure or manual exposure as default
E000 Fuser did not heat up
E001 Fuser temperature too high
E002 Fuser temperature not rising at correct pace
E003 Fuser temperature drops
E004 SSR shorted
E210 Lens home problem
E212 Lens home problem
E220 Exposure lamp problem
E224 Blank shutter home problem
E240 DC controller or composite power supply problem
E400 Data communication problem
E401 Pickup motor problem
E402 Belt motor problem
E403 Feeder motor
E404 Delivery motor
E411 Document detect sensor
E500 Communication problem with copier
E510 Feeder motor
E530 Home sensor
E531 Staple swing sensor problem
E540 Bin shift motor rotation problem
E541 Bin motor
E710 DC controller
E711 Document feeder IC failure
E716 Cassette feed IC failure
E800 Auto power-off circuit problem
E901 Cassette feed motor
E902 Paper guide home sensor problem
E000 The temperature of the upper fixing roller does not reach 100 C within 5 min after powering-on.
E000 Low fuser temperature
E000 Fuser Problem
E001 High fuser temperature
E001 The temperature of the upper fixing assembly remains 230 C or more for 5 seconds or more.
E002 Fuser temperature not rising at the correct pace
The temperature of the upper fixing roller does not reach 180 C within 5 min after it has exceeded
E002
100 C.
The temperature of the upper fixing roller is below 100 C or less for 5 seconds after it has reached
E003
180 C.
E003 Fuser temperature not rising at the correct pace
E005 Fuser cleaner belt problem
E005 The length of the cleaning belt taken up (fixing assembly) is more than a specified length.
E010 Drive problem (main motor)
In response to the main motor drive signal, two or more clock pulses are not generated within 1
E010
second.
E013 Toner waste problem
When rotation of waste toner feeder screw becomes disabled and the sensor switch (SW20) is
E013
pressed.
During copying operation, the black toner supply signal is "0" (no toner) for 3 min or more. At time of
E020 installation, the black toner supply signal does not go "1" within 6 min during black toner supply
sequence.
E020 No toner being fed for 3 min after toner was called for
E030 A counter open circuit is identified when counter drive is OFF.
E030 Counter
The tray home position signal (THP) is not generated within 4 sec while the paper guide motor dive
E050
signal is generated.
E050 Duplex problem
E203 Scan home problem
The scanner home position signal (SCHP) is generated 2 pulses or more within 0.5 sec when the
E203
scanner motor is turned ON.
The lens x home position signal (LXHP) is not generated within 9 sec after the power switch or the
E210
door switch is turned ON. The lens x home position signal (LXHP) is generated for 2 sec or more.
E210 Lens home problem
E212 Lens home problem
The lens y home position signal (LYHP) is not generated within 9 sec after the power switch or the
E212
door switch is turned ON. The lens y home position signal (LYHP) is generated for 2 sec or more.
E400 Communication problem with copier
E401 Pickup motor or motor sensor
E402 Belt motor or motor sensor
E403 Feed motor or motor sensor
E404 exit motor or motor sensor
E405 Pick up motor sensor
E406 Side guard motor or motor sensor
E407 Tray motor or position sensor
E411 Sensor for document detection
E431 Sub registration sensor
E441 Motor
E442 Cooling fan problem
E446 CFF mirror motor or sensor
E447 CFF out of position or bad position sensor
E500 Communication problem with copier
E510 Feed motor drive
E513 Tandem feed motor drive
E530 Staple guide motor or sensor
E531 Stapler swing motor
E540 Bin shifting motor
E710 Q124 on the DC controller PCB cannot be initialized at power-on.
E710 DC controller (main board)
E711 DC controller
E711 Q124 on the DC controller is faulty after power-on.
E712 The communication IC on the RDF-A1 controller is faulty.
E712 24 volt power supply or RDF-A1 main board
E715 The communication IC on the C.F.F. controller PCB is faulty.
E715 Computer form feeder board problem
An open circuit is identified in the auto power-off mechanism. The auto power-off signal is generated
E800
twice or more in 2 sec.
E800 Auto power shut off problem. Main board
E2 Scanner
EO Heat lamp
E000 Fuser thermistor, heater thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac.
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407
E010 Main motor drive problem
E030 Counter
E041 Paper deck motor, clutch or sensor
E064 Composite power supply or main motor board
E202 Scan problem. Motor sensor.
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply.
E260 Main board, power supply cooling fan or composite power supply.
E261 Composite power supply or fluctuating power.
E400 ADF communication to machine.
E401 ADF pickup motor or sensor.
E402 ADF belt motor drive
E403 ADF feed motor or slip sensor.
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem.
E510 Sorter drive problem.
E530 Stapler guide bar motor.
E531 Stapler swing motor.
E540 Bin shift motor.
E541 Bin motor drive problem.
E710 Main board (DC controller.)
E711 Main board (DC controller.)
E712 Main board or communication problem with ADF, or ADF main board.
Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.
E717
Reset with user
E802 Composite power supply or DC controller.
E901 Cassette feed unit board or cassette feed motor.
E902 Horizontal registration problem. I think this refers to the duplex section.
J1 Feed jam
J10 Duplex exit jam
J11 Vertical jam
J12 Vertical jam
J13 Vertical jam
J14 Vertical jam
J15 Deck jam
J2 Feed jam
J3 Separation area jam
J4 Separation area jam
J5 Exit jam
J6 Exit jam
J7 Sorter jam
J8 Door open jam
J9 Cassette jam
JA Cassette jam
Jb Cassette jam
JC Cassette jam
Jd Duplex feed jam
JE Duplex exit jam
JF Duplex registration jam
Коды ошибок копировальных аппаратов

Canon NP112
Code Description
E2 Scanner
EO Heat lamp
Коды ошибок копировальных аппаратов

Canon NP6521
Code Description
E000 Fuser thermistor, heater thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac.
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407
E010 Main motor drive problem
E030 Counter
E041 Paper deck motor, clutch or sensor
E064 Composite power supply or main motor board
E202 Scan problem. Motor sensor.
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply.
E260 Main board, power supply cooling fan or composite power supply.
E261 Composite power supply or fluctuating power.
E400 ADF communication to machine.
E401 ADF pickup motor or sensor.
E402 ADF belt motor drive
E403 ADF feed motor or slip sensor.
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem.
E510 Sorter drive problem.
E530 Stapler guide bar motor.
E531 Stapler swing motor.
E540 Bin shift motor.
E541 Bin motor drive problem.
E710 Main board (DC controller.)
E711 Main board (DC controller.)
E712 Main board or communication problem with ADF, or ADF main board.
Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies.
E717
Reset with user
E802 Composite power supply or DC controller.
E901 Cassette feed unit board or cassette feed motor.
E902 Horizontal registration problem. I think this refers to the duplex section.
J1 Feed jam
J10 Duplex exit jam
J11 Vertical jam
J12 Vertical jam
J13 Vertical jam
J14 Vertical jam
J15 Deck jam
J2 Feed jam
J3 Separation area jam
J4 Separation area jam
J5 Exit jam
J6 Exit jam
J7 Sorter jam
J8 Door open jam
J9 Cassette jam
JA Cassette jam
Jb Cassette jam
JC Cassette jam
Jd Duplex feed jam
JE Duplex exit jam
JF Duplex registration jam
Коды ошибок копировальных аппаратов

Canon PC 710/850
Code Description
C No problem. Means that the machine is correcting the fuser film tracking.
Drum must be changed. Could be the drum serial number is identified by the logic as being
CC
non-compatible to that particular copier.
E000 Low fuser temperature
E001 High fuser temperature
E002 High fuser temperature
E003 Erratic fuser temperature
E007 Fuser film off track and will not repair itself
E010 Main drive problem
E030 Counter problem
E064 Scan problem, or power supply
E202 Scan problem
E210 Lens drive problem or lens sensor
E220 Exposure lamp stays on or off
E240 DC controller (main board) or composite power supply
E261 Zero cross problem. Power frequency or composite power supply
E400 Communication problem between boards
E803 24 volt problem
EO Fuser problem
H Fuser overheat
E000 Fuser thermistor, heater, thermal fuse
E001 Fuser thermistor, or triac
E002 Fuser thermistor, thermal fuse or triac
E003 Fuser thermistor, heater, thermal fuse or triac
E004 Triac or fuser won’t shut off
E007 Fuser film is off center or not driving properly
E010 Main motor drive problem
E030 Counter
E064 Composite power supply or main board
E202 Scan problem
E210 Lens drive problem
E220 Exposure lamp
E240 Main board or composite power supply
E261 Composite power supply or fluctuating power
E400 ADF communication problem to machine
E402 ADF belt motor drive
E404 ADF exit motor
E411 ADF document detect, or registration sensor or edge sensor
E500 Sorter communication problem
E510 Sorter drive problem
E530 Stapler guide bar motor
E531 Stapler swing motor
E540 Bin shift motor
E541 Bin motor drive problem
E710 Main board
E711 Main board
E712 Main board or communication problem with ADF
E717 Main board, asst. board
U0 Initializing. Sets all user modes to factory default settings
U1 Auto clear timer. Range 1-9. Each digit=1 minute
U2 Automatic power shut off timer
U3 Fine adjustment of zoom
U4 Auto cassette switching
U5 Sort or non-sort default
U6 Cleans document feeder pickup assembly
U7 CLEAR "replace drum"
U9 Auto exposure or manual exposure as default
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
E2 Scan
EO Heater
E2 Scan
EO Heater
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
E2 Scan
EO Heater
E000 Fuser problem
E001 Fuser problem
E010 Drive
E210 Zoom/lens/motor problem
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20
E00
seconds
E001 Shorted thermistor or high-temperature, Exit sensor
E010 Clock Pulse
E210 Zoom Lens Problem
Коды ошибок копировальных аппаратов

Canon PC-1
Code Description
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
Коды ошибок копировальных аппаратов

Canon PC-2
Code Description
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
Коды ошибок копировальных аппаратов

Canon PC3
Code Description
E2 Scan
EO Heater
Коды ошибок копировальных аппаратов

Canon PC5
Code Description
E2 Scan
EO Heater
E2 Scan
EO Heater
Коды ошибок копировальных аппаратов

Canon PC-5
Code Description
E1 The heater film has gone off center. Turn machine off & on, make sure it’s level etc.
E2 Scan problme
E6 Exposure lamp or exposure lamp sensor
EO Heater problem
Коды ошибок копировальных аппаратов

Canon PC5L
Code Description
E2 Scan
EO Heater
Коды ошибок копировальных аппаратов

Canon PC6
Code Description
E000 Fuser problem
E001 Fuser problem
E010 Drive
E210 Zoom/lens/motor problem
Коды ошибок копировальных аппаратов

Canon PC7
Code Description
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20
E00
seconds
E001 Shorted thermistor or high-temperature, Exit sensor
E010 Clock Pulse
E210 Zoom Lens Problem
Коды ошибок копировальных аппаратов

Gestetner 2217ZD
Code Description
C2 Drive problem
C3 Scan problem
C4 Lens problem
C5 Coronas
C6 Heater problem or only 1 of the 2 front door interlocks switches is actuated
CO Main board problem Run simulation 90. Try power off/on
Коды ошибок копировальных аппаратов

Konica 1015 Konica 3290
Konica 1018 Konica 3340
Konica 1112 Konica 4045
Konica 1120 Konica 4065
Konica 1212 Konica 4145
Konica 1290 Konica 4155
Konica 1290RE Konica 4255
Konica 1590 Konica 4290
Konica 1790 Konica 4345
Konica 2020 Konica 4355
Konica 2028 Konica 5080
Konica 2125 Konica 6090
Konica 2130 Konica 7490
Konica 2203
Konica 2290
Konica 2590
Konica 3035
Konica 3135
Konica 3240
Коды ошибок копировальных аппаратов

Konica 1015
Code Description
F09 Power leakage of some kind. Heat, exposure, AC or power supply.
F23 Toner motor
Toner density adjustment problem. This means machine is undertoned. To repair, replace developer
and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that
F26
you should disconnect the toner motor first. This code happens probably because either machine
wasn’t set up properly, or the customer kept on using the machine with the toner light on.
F28 Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"
F34 High fuser temperature*
F35 Low fuser temperature*
F36 Low fuser temperature*
F41 Scan home
F42 Scan home
F43 Exposure lamp
F45 Lens problem
F54 Fan motor
F60 ADF to main board communication problem
F67 ADF encoder
F77 Sorter gate
F88 AE adjustment problem
J11 Feed jam
J12 Feed jam
J13 Feed jam
J16 Jam inside
J31 Exit jam
J32 Exit jam
J61 ADF jam
J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P20 Drum unit or toner level connection problem
300 copies have been run since toner light came on. Depending on how 25 mode, code 92 is set,
P25
machine may not work at all.
P26 Must adjust TDS????in 47 mode
P64 ADF & operator are confused
P68 ADF feed problem
P69 ADF feed problem
P71 Sorter interlock
P81 Key counter not installed
Коды ошибок копировальных аппаратов

Konica 1018
Code Description
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter code 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13 Paper feed jam
J14 Paper feed jam
J15 Duplex unit jam
J16 Feed jam
J17 Feed jam
J19 Paper feed jam
J31 Exit jam
J32 Exit jam
J61 ADF opened during run
J62 ADF jam
J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92 Duplex stack gate sensor or other duplex problem
J93 Duplex stack gate sensor or other duplex problem
J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex
Коды ошибок копировальных аппаратов

Konica 1112
Code Description
16 Feed jam
20 Toner level detector problem or loose connection
23 Toner feed problem
25 Toner. Means that 100 copies have been made since toner light came on
26 Toner density problem
31 Exit jam
32 Exit jam
34 Fuser temperature too high
35 Fuser temperature too low
36 Fuser problem. Heat, thermistor, etc.
41 Scan return
42 Scan forward
43 Exposure lamp
50 Problem with IC8
52 Encoder (pulse sensor, PT; drive problem)
Коды ошибок копировальных аппаратов

Konica 1120
Code Description
04 PTC heater. Don’t know what this is, but "0" means it is not installed. 1 means it is.
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode"
F09
and select "P49" and reset to "0"
F23 Toner motor
Toner density adjustment problem. This means the machine is undertoned. To repair, replace
developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some
F26
feel you should disconnect the toner motor first. This code happens probably because either the
machine wasn’t set up properly, or because the customer kept using the machine with the light on.
F28 Corona problem. Could be any corona.
F34 High fuser temperature.
F35 Low fuser temperature.
F36 Low fuser temperature.
F41 Scan home
F42 Scan home
F43 Exposure lamp or exp. Lamp board.
F44 Lens drive problem.
F45 Lens problem.
F54 Fan motor.
F60 ADF to main board communication problem.
F67 ADF encoder (pulse sensor, drive problem)
F70 Sorter to machine communication problem.
F77 Sorter gate.
F88 AE adjustment problem.
J11 Feed jam
J12 Feed jam
J13 Feed jam
J14 Jam inside
J15 Jam inside
J16 Jam inside
J31 Exit jam
J32 Exit jam
J61 ADF jam
J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P11 Count. For total count, select "0". For developer count, select "5".
P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15 Size priority. 0 is standard. 1 is a size priority.
P16 Paper size priority.
P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20 Drum unit or toner level connection problem. Most likely, a loose connection.
P22 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P23 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
300 copies have been run since toner light came on, depending on how 25 mode, code 92 is set,
P25
machine may not work at all.
P26 ADF border erase. 0 for none. 5 for 5mm.
P26 Must replace and calibrate developer.
P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27 Toner density sensor unplugged or toner density sensor problem.
P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64 ADF & operator are confused. Remove original.
P68 ADF feed problem.
P69 ADF feed problem.
P71 Sorter interlock.
P81 Key counter not installed.
Коды ошибок копировальных аппаратов

Konica 1212
Code Description
04 PTC heater. Don’t know what this is, but "0" means it is not installed. 1 means it is.
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode"
F09
and select "P49" and reset to "0"
F23 Toner motor
Toner density adjustment problem. This means the machine is undertoned. To repair, replace
developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some
F26
feel you should disconnect the toner motor first. This code happens probably because either the
machine wasn’t set up properly, or because the customer kept using the machine with the light on.
F28 Corona problem. Could be any corona.
F34 High fuser temperature.
F35 Low fuser temperature.
F36 Low fuser temperature.
F41 Scan home
F43 Exposure lamp or exp. Lamp board.
F44 Lens drive problem.
F45 Lens problem.
F54 Fan motor.
F60 ADF to main board communication problem.
F67 ADF encoder (pulse sensor, drive problem)
F70 Sorter to machine communication problem.
F77 Sorter gate.
F88 AE adjustment problem.
J11 Feed jam
J12 Feed jam
J13 Feed jam
J14 Jam inside
J15 Jam inside
J16 Jam inside
J31 Exit jam
J32 Exit jam
J61 ADF jam
J62 ADF jam
J63 ADF exit jam
J72 Sorter jam
P11 Count. For total count, select "0". For developer count, select "5".
P12 Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15 Size priority. 0 is standard. 1 is a size priority.
P16 Paper size priority.
P19 Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20 Drum unit or toner level connection problem. Most likely, a loose connection.
P22 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P23 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P24 Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
300 copies have been run since toner light came on, depending on how 25 mode, code 92 is set,
P25
machine may not work at all.
P26 ADF border erase. 0 for none. 5 for 5mm.
P26 Must replace and calibrate developer.
P27 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27 Toner density sensor unplugged or toner density sensor problem.
P28 PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64 ADF & operator are confused. Remove original.
P68 ADF feed problem.
P69 ADF feed problem.
P71 Sorter interlock.
Коды ошибок копировальных аппаратов

Konica 1290
Code Description
16 Feed jam
20 Toner sensor connector
25 Toner light has been on for 100 copies
26 Toner density sensor
31 Exit switch not actuated
32 Exit jam
34 Fuser problem
35 Low fuser temperature
36 High fuser temperature
41 Scan did not return home
42 Scan problem
43 Exposure lamp problem
50 Board problem
52 Drive problem
85 No waste bottle
16 Feed jam
20 Toner sensor connector
25 Toner light has been on for 100 copies
26 Toner density sensor
31 Exit switch not actuated
32 Exit jam
34 Fuser problem
35 Low fuser temperature
36 High fuser temperature
41 Scan did not return home
42 Scan problem
43 Exposure lamp problem
50 Board problem
52 Drive problem
85 No waste bottle
Коды ошибок копировальных аппаратов

Konica 1290RE
Code Description
16 Feed jam
20 Toner sensor connector
25 Toner light has been on for 100 copies
26 Toner density sensor
31 Exit switch not actuated
32 Exit jam
34 Fuser problem
35 Low fuser temperature
36 High fuser temperature
41 Scan did not return home
42 Scan problem
43 Exposure lamp problem
50 Board problem
52 Drive problem
85 No waste bottle
Коды ошибок копировальных аппаратов

Konica 1590
Code Description
F23 Toner motor problem
F24 Pre-clean lamp
F26 Toner ratio
F34 High fuser temperature
F35 Low fuser temperature
F36 Thermistor
F41 Scan home
F42 Forward scan exposure lamp
F43 Exposure lamp
F45 Lens drive
F50 Board problem
F52 Drive
F77 Sorter bin sensor
J12 Paper feed jam
J13 Paper feed jam
J16 Paper feed jam
J31 Jam under drum
J32 Exit jam
J72 Sorter jam
P20 Drum not installed properly
P71 Sorter cover
Коды ошибок копировальных аппаратов

Konica 1790
Code Description
F34 High fuser temperature
F35 Low fuser temperature
F36 Open thermistor or incomplete warm up
F41 Scan home problem
F42 Scan problem
F43 CVR board problem
F45 Lens drive
F52 Drive
F55 Zero cross problem
F67 ADF drive
F77 Sorter drive
J11 Upper cassette jam
J12 Lower cassette jam
J14 LCT jam
J16 Cassette jam
J31 Jam under drum
J32 Jam under drum
J62 ADF jam
J63 ADF jam
J72 Sorter jam
P14 LCT open
P61 ADF up
P64 Original on glass
P69 ADF original jam
P71 Sorter cover open
P81 Key counter out
Коды ошибок копировальных аппаратов

Konica 2020
Code Description
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter code 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13 Paper feed jam
J14 Paper feed jam
J15 Duplex unit jam
J16 Feed jam
J17 Feed jam
J19 Paper feed jam
J31 Exit jam
J32 Exit jam
J61 ADF opened during run
J62 ADF jam
J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92 Duplex stack gate sensor or other duplex problem
J93 Duplex stack gate sensor or other duplex problem
J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex
Коды ошибок копировальных аппаратов

Konica 2028
Code Description
F18 Paper lift did not complete
F23 Toner motor
F24 Pre clean lamp problem
F26 Toner density sensor
F34 Fuser overheat
F35 Fuser temperature too low. Lamp, thermofuse open wire
F36 Fuser temperature erratic. Probably thermistor
F41 End of scan sensor not actuated
F42 End of scan sensor not reached
F43 CVR (copy lamp voltage regulator)
F45 Lens or mirror movement problem
F52 Drive problem
F55 Zero cross.
F56 Waste toner collector box is full. After replacing it, you must enter code 94 in the 47 mode to reset
F60 ADF/machine interface problem
F67 ADF drive problem
F70 Sorter/machine interface problem
F77 Sorter bin problem
F78 Stapler problem
F86 Waste toner see 56
F98 Duplex problem
J11 Upper cassette
J12 Lower cassette
J13 Paper feed jam
J14 Paper feed jam
J15 Duplex unit jam
J16 Feed jam
J17 Feed jam
J19 Paper feed jam
J31 Exit jam
J32 Exit jam
J61 ADF opened during run
J62 ADF jam
J63 ADF jam
J65 RADF reverse jam
J72 Sorter jam, or sorter interlock opened
J75 Stapler jam
J92 Duplex stack gate sensor or other duplex problem
J93 Duplex stack gate sensor or other duplex problem
J94 Duplex stack gate sensor or other duplex problem
J95 Duplex motor or duplex jam
P17 Right door
P19 Right door of paper feed unit
P20 Drum not installed properly or toner level sensor connection problem
P33 Left door
P61 RADF reverse cover open
P64 ADF was selected at the wrong time
P71 Sorter interlock
P74 Stapler overloaded, or paper left in stapler bin
P76 Out of staples
P81 Key counter not installed
P82 Memory card problem
P96 Paper in stacker when duplex selected
P97 Used bypass in duplex mode
P99 More than one side than the other in duplex
Коды ошибок копировальных аппаратов

Konica 2125
Code Description
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan return problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between the machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter bin problem
F78 No memory card installed
F86 Too many copies were made after toner waste was full. Reset with 47 mode, code 94.
F98 Duplex guide plate does not return home quickly enough
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14 Lower paper feed unit jam
J15 Lower paper feed unit jam
J16 Jam in machine
J17 Jam in machine
J19 Paper feed unit jam
J21 Jam around drum
J31 Exit jam
J32 Exit jam
J61 RDH/RADF jam or open
J62 RDH/RADF jam
J63 RADF exit jam
J72 Sorter jam or open interlock
J74 Finisher problem
J75 Stapler problem
J92 Duplex jam
J93 Duplex jam
J94 Duplex jam
J95 Duplex jam
P17 Right side door open
P19 Paper feed unit door open
P33 Exit door open
P51 Front door open
P61 RADF cover open
P64 RADF not opened to remove originals
P68 Original removed during operation of RADF
P69 Original didn’t feed during RADF/RDH operation
P71 Sorter interlock
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals
P74
were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76 Out of staples
P78 Stapler not installed
P81 Key counter not plugged in
Memory card not installed, not formatted to Konica specs, or no machine serial number registered on
P82
memory card
P86 No toner waste box
P91 Duplex unit pulled out
P96 Paper in duplex tray
P97 Bypass was used or attempted during duplex.
P99 Too many reverse side copies during duplex
Коды ошибок копировальных аппаратов

Konica 2130
Code Description
F18 Paper feed lift problem
F18-3 LCT problem
F18-4 LCT problem
F28-1 Charge corona
F28-2 Transfer or separator corona
F34-1 High fuser temperature
F34-2 High fuser temperature
F35-1 Low fuser temperature
F35-2 Low fuser temperature
F36-1 Low fuser temperature
F36-2 Low fuser temperature
F41 Scan return problem
F42 Scan forward problem
F43 Exposure lamp board problem
F45 Lens home problem
F52 Main motor drive problem
F55 Zero cross of DC power supply
F60 Communication interruption between the machine and RADF
F67 RDH or RADF drive problem
F70 Communication problem between machine and sorter
F77 Sorter bin problem
F78 No memory card installed
F86 Too many copies were made after toner waste was full. Reset with 47 mode, code 94.
F98 Duplex guide plate does not return home quickly enough
J10 Feed jam
J11 Upper feed jam
J12 Lower feed jam
J13 Upper paper feed unit jam
J14 Lower paper feed unit jam
J15 Lower paper feed unit jam
J16 Jam in machine

<<

стр. 2
(всего 13)

СОДЕРЖАНИЕ

>>