<<

стр. 5
(всего 13)

СОДЕРЖАНИЕ

>>

OP Toner hopper lid
C1 Drive
C5 Charge corona
C6 Transfer/separator corona
C7 Heat
OP Toner hopper lid
Коды ошибок копировальных аппаратов

Mita 111C
Code Description
C1 Drive
C5 Charge corona
C6 Transfer/separator corona
C7 Heat
OP Toner hopper lid
Коды ошибок копировальных аппаратов

Mita 113
Code Description
C1 Drive
C1 Drive
C5 Charge corona
C5 Charge corona
C6 Transfer/separator corona
C6 Transfer/separator corona
C7 Heat
C7 Heat
OP Toner hopper lid
OP Toner hopper lid
Коды ошибок копировальных аппаратов

Mita 114
Code Description
C2 Main drive
C2 Main Drive
C3 Scan
C3 Scan
C5 Corona
C5 Corona
C6 Heat
C6 Heat
Коды ошибок копировальных аппаратов

Mita 1205
Code Description
C3 Scan
C6 Fuser
Коды ошибок копировальных аппаратов

Mita 1256
Code Description
AP CC50. Toner being mixed
C01 Memory problem. Main board or simulation 70 required
C02 EEPROM or main board
C21 Drive problem (CC50/1256)
C30 Scan
C40 Lens drive
C61 Fuser problem. No heat or open circuit
C63 Fuser thermistor open
C64 Fuser thermistor. Short or high fuser temperature
C72 1256 drum thermistor open
C73 1256 drum thermistor shorted
C74 CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup
C74 1257 Developer thermistor
C75 CC50/1256 Drum unit switch problem or drum setup problem
C75 1257 developer thermistor
C76 May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78.
J01 Feed jam
J02 Drum or fuser area jam
J03 Jam
OF 1256 drum & developer units must be replaced
OP Front door open
PE/PF No paper, no paper feed problem
U1 Total counter
CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum
Ub
one full revolution
CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white
Uc plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic
blocker back up.
UF Toner or developer not installed properly
Коды ошибок копировальных аппаратов

Mita 1257
Code Description
AP CC50. Toner being mixed
C01 Memory problem. Main board or simulation 70 required
C02 EEPROM or main board
C21 Drive problem (CC50/1256)
C30 Scan
C40 Lens drive
C61 Fuser problem. No heat or open circuit
C63 Fuser thermistor open
C64 Fuser thermistor. Short or high fuser temperature
C72 1256 drum thermistor open
C73 1256 drum thermistor shorted
C74 CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup
C74 1257 Developer thermistor
C75 CC50/1256 Drum unit switch problem or drum setup problem
C75 1257 developer thermistor
C76 May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78.
J01 Feed jam
J02 Drum or fuser area jam
J03 Jam
OF 1256 drum & developer units must be replaced
OP Front door open
PE/PF No paper, no paper feed problem
U1 Total counter
CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum
Ub
one full revolution
CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white
Uc plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic
blocker back up.
UF Toner or developer not installed properly
Коды ошибок копировальных аппаратов

Mita 1355
Code Description
AP Toner being mixed
C01 Memory problem. Main board or simulation 70 required
C02 EEPROM or main board
C21 Drive problem
C30 Scan, motor, switch
C40 Lens drive
C61 Fuser problem. No heat or open circuit
C63 Fuser thermistor open
C64 Fuser thermistor open
C72 Drum thermistor open. Blank lamps
C73 Drum thermistor shorted
C74 Developer thermistor
C75 Drum unit switch problem or drum setup problem
C76 Waste toner full, reset with simulation 78.
J01 Feed jam
J02 Drum or fuser area jam
J03 Jam
OF Drum & developer units must be replaced (entire process unit)
OP Front door open
PE/PF No paper or paper feed problem
U1 Total counter
Old developer unit and new drum. Might be upset by replacing the fuse, or by turning the drum
Ub
through one full revolution
New developer unit and old drum. On rear drum is a lock. Inside the opening is a white plastic that
Uc snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back
up
UF Toner or developer not installed properly. Bad toner sensor
Коды ошибок копировальных аппаратов

Mita 1415
Code Description
C3 Scan problem
Fuser problem. Temperature too low, too high, open thermistor. Heat lamp, thermofuse, thermistor,
C6
etc
PE Paper empty
Коды ошибок копировальных аппаратов

Mita 142RE
Code Description
C1 Drive
C2 Optics
C5 Main corona
C6 Transfer/separator corona
C7 Heat, thermistor, thermofuse
Коды ошибок копировальных аппаратов

Mita 1435
Code Description
C01 Battery or main board. Simulation 70 might clear
C30 Scan problem
C31 Scan problem
C32 Scan reverse problem
C40 Lens motor
C5 Lamp Problem
C61 Low fuser temperature. Heat lamp, thermofuse.
C62 Low fuser temperature
C63 Fuser thermistor
C64 High fuser temperature. Triac, pinched wire
C73 Shorted DV unit thermistor
PE Paper empty
Коды ошибок копировальных аппаратов

Mita 1455
Code Description
C01 Battery or main board. Simulation 70 might clear
C30 Scan problem
C31 Scan problem
C32 Scan reverse problem
C40 Lens motor
C61 Low fuser temperature. Heat lamp, thermofuse.
C62 Low fuser temperature
C63 Fuser thermistor
C64 High fuser temperature. Triac, pinched wire
C73 Shorted DV unit thermistor
PE Paper empty
Коды ошибок копировальных аппаратов

Mita 152Z
Code Description
C2 Drive section
C2 Drive section
C4 Lens unit
C4 Lens unit
C5 Corona
C5 Corona
C6 Heater
C6 Heater
Коды ошибок копировальных аппаратов

Mita 1560
Code Description
C01 NVRAM problem.
C20 Main drive problem
C30 Scan problem. Scan sensors, scan motor, belt tension, cable tension, etc
C40 Lens motor problem, lens sensor motor
C50 Corona problem: Broken wire, shorted blocks, bad corona, high voltage transformer
Low fuser temperature. Problem with heat lamp, connections, thermal switch, thermistor or main
C61
board
C63 Open fuser thermistor
C64 Shorted fuser thermistor
C72 Open drum thermistor
C73 Shorted drum thermistor
C74 Open external thermistor
C75 Shorted external thermistor
C90 Communication problem between copier and ADF
J30 Jam in registration area
J40 Jam inside machine or fuser
J50 Exit jam or fuser jam
PF Paper feed
Коды ошибок копировальных аппаратов

Mita 1605
Code Description
C01 Memory
C20 Drive
C30 Scan
C31 Scan return*
C32 Scan motor*
C33 Scan motor brake*
C40 Lens motor or mirror motor*
C50 Charge corona
C51 T/S corona
C60 High temperature
C61 Fuser thermistor
C62 No warm up
C63 Fuser temperature drops
C70 Drum thermistor short
C71 Drum thermistor open
Коды ошибок копировальных аппаратов

Mita 1655
Code Description
C2 Drive section
C4 Lens unit
C5 Corona
C6 Heater
Коды ошибок копировальных аппаратов

Mita 1656
Code Description
C01 Memory
C20 Drive
C30 Scan
C31 Scan return*
C32 Scan motor*
C33 Scan motor brake*
C40 Lens motor or mirror motor*
C50 Charge corona
C51 T/S corona
C60 High temperature
C61 Fuser thermistor
C62 No warm up
C63 Fuser temperature drops
C70 Drum thermistor short
C71 Drum thermistor open
Коды ошибок копировальных аппаратов

Mita 1685
Code Description
C01 Memory
C20 Drive
C30 Scan
C31 Scan return*
C32 Scan motor*
C33 Scan motor brake*
C40 Lens motor or mirror motor*
C50 Charge corona
C51 T/S corona
C60 High temperature
C61 Fuser thermistor
C62 No warm up
C63 Fuser temperature drops
C70 Drum thermistor short
C71 Drum thermistor open
Коды ошибок копировальных аппаратов

Mita 1755
Code Description
AP Toner is mixing
Memory loss. Use simulation 70 to try and repair. Otherwise must replace main
C01
board
C21 Main drive problem
C31 Scan problem
C41 Lens problem
C42 Mirror motor problem
C51 Charge corona problem
C52 Transfer corona problem
C61 Low fuser temperature. Lamp, thermofuse, connections, etc.
C63 Fuser thermistor
C64 Fuser thermistor short
C72 Drum thermistor
C73 Drum thermistor short
LED(orange) Paper feed motor problem, or sensor
LED(orange,flashing) ADF interlock
LED(red) ADF open sensor
OP Front door open of optional cassette is open
U1 Key counter
Коды ошибок копировальных аппаратов

Mita 1785
Code Description
C2 Drive problem
C3 Scan problem
C4 Lens problem
C5 Coronas
C6 Heater problem or only 1 of the 2 front door interlocks switches is actuated
CO Main board problem Run simulation 90. Try power off/on
Коды ошибок копировальных аппаратов

Mita 1856
Code Description
AP Toner is feeding
C01 Backup memory problem.
C03 Communication problem between main board and scan drive board
C05 Ground problem having to do with main board and power relay. Possible short
C07 Operation panel thermistor is shorted. Scan motor
C21 Main drive problem
C22 Side to side registration motor problem in duplex unit
C23 Desk drive motor drive problem
C24 Paper deck paper conveying motor
C31 Scan problem. Scan sensors, scan motor, scan motor drive board, belt tension, cable tension.
C41 Lens motor problem
C42 Scan mirror problem
C51 Charge corona problem
C52 Transfer/separator corona problem
C61 Low fuser temperature
C63 Open fuser thermistor
C64 Shorted drum thermistor
C72 Open drum thermistor
C73 Shorted drum thermistor
C81 Sorter/stapler feed motor drive problem
C82 Sorter/stapler bin shift motor problem
C83 Sorter/stapler guide bar motor or guide bar motor sensor
C84 Sorter/stapler slide motor problem or sensor problem
C91 RADF original feed motor drive problem; motor, pulse sensor, etc
C92 RADF belt drive motor drive problem; motor pulse sensor, RADF main board
C93 RADF loop motor problem. Loop motor, pulse sensor or RADF main board.
OP Cover or door open
PF Paper feed
U1 Key counter missing
Коды ошибок копировальных аппаратов

Mita 2055
Code Description
AF Original on document feeder placed wrong
C00 Battery problem or main board
C01 Battery problem or main board
C2 Drive problem
C20 Drive problem
C21 Duplex side to side registration
C3 Scan
C4 Lens motor
C40 Lens motor
C41 Mirror motor
C5 Coronas
C6 Low fuser temperature
C60 High fuser temperature
C61 Loe fuser temperature
C7 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C70 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C71 DV unit shift problem; color unit dip switch; bad fuser thermofuse
U1 Key counter
UF Color unit out
Коды ошибок копировальных аппаратов

Mita 2105
Code Description
C1 Paper feed problem (more than 6 times = PF)
C2 Drive
C2 Drive
C2 Drive
C3 Scan
C3 Scan
C3 Scan
C3 Scanner problem
C5 Corona
C5 Corona
C5 Corona
C6 Heat problem
C6 Fuser
C6 Fuser
C6 Fuser
H0 Battery problem
H0 Batter
HO Battery problem
U1 Key counter
U1 Key counter
U1 Key counter
Коды ошибок копировальных аппаратов

Mita 211
Code Description
C1 Scanner home problem/constant jams
C2 Motor, clock pulse
C3 Scanner problem
C4 Exposure lamp
C5 Blank lamp
C6 Coronas
C7 Heater
C8 Heater
Коды ошибок копировальных аппаратов

Mita 213
Code Description
C1 Scanner home problem, constant jams
C2 Motor, clockpulse
C3 Scanner problems
C4 Exposure lamp
C5 Blank lamp
C6 Coronas
C7 Heater
C9 Lens motor
CA Sorter
CB Document feeder
C1 Scanner home problem/constant jams
C2 Motor, clock pulse
C3 Scanner problem
C4 Exposure lamp
C5 Blank lamp
C6 Coronas
C7 Heater
C8 Lens motor
CA Sorter
CB Document feeder
Коды ошибок копировальных аппаратов

Mita 213RE
Code Description
C1 Scanner home problem/constant jams
C2 Motor, clock pulse
C3 Scanner problem
C4 Exposure lamp
C5 Blank lamp
C6 Coronas
C7 Heater
C8 Lens motor
CA Sorter
CB Document feeder
Коды ошибок копировальных аппаратов

Mita 2254
Code Description
AF Original on document feeder placed wrong
C00 Battery problem or main board
C01 Battery problem or main board
C2 Drive problem
C20 Drive problem
C21 Duplex side to side registration
C3 Scan
C4 Lens motor
C40 Lens motor
C41 Mirror motor
C5 Coronas
C6 Low fuser temperature
C60 High fuser temperature
C61 Loe fuser temperature
C7 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C70 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C71 DV unit shift problem; color unit dip switch; bad fuser thermofuse
U1 Key counter
UF Color unit out
Коды ошибок копировальных аппаратов

Mita 2255
Code Description
AF Original on document feeder placed wrong
C00 Battery problem or main board
C01 Battery problem or main board
C2 Drive problem
C20 Drive problem
C21 Duplex side to side registration
C3 Scan
C4 Lens motor
C40 Lens motor
C41 Mirror motor
C5 Coronas
C6 Low fuser temperature
C60 High fuser temperature
C61 Loe fuser temperature
C7 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C70 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C71 DV unit shift problem; color unit dip switch; bad fuser thermofuse
U1 Key counter
UF Color unit out
Коды ошибок копировальных аппаратов

Mita 2285
Code Description
AF Original on document feeder placed wrong
C00 Battery problem or main board
C01 Battery problem or main board
C2 Drive problem
C20 Drive problem
C21 Duplex side to side registration
C3 Scan
C4 Lens motor
C40 Lens motor
C41 Mirror motor
C5 Coronas
C6 Low fuser temperature
C60 High fuser temperature
C61 Loe fuser temperature
C7 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C70 DV unit shift problem; color unit dip switch; bad fuser thermofuse
C71 DV unit shift problem; color unit dip switch; bad fuser thermofuse
U1 Key counter
UF Color unit out
Коды ошибок копировальных аппаратов

Mita 2355
Code Description
AP Toner is feeding
C01 Backup memory problem.
C03 Communication problem between main board and scan drive board
C05 Ground problem having to do with main board and power relay. Possible short
C07 Operation panel thermistor is shorted. Scan motor
C21 Main drive problem
C22 Side to side registration motor problem in duplex unit
C23 Desk drive motor drive problem
C24 Paper deck paper conveying motor
C31 Scan problem. Scan sensors, scan motor, scan motor drive board, belt tension, cable tension.
C41 Lens motor problem
C42 Scan mirror problem
C51 Charge corona problem
C52 Transfer/separator corona problem
C61 Low fuser temperature
C63 Open fuser thermistor
C64 Shorted drum thermistor
C72 Open drum thermistor
C73 Shorted drum thermistor
C81 Sorter/stapler feed motor drive problem
C82 Sorter/stapler bin shift motor problem
C83 Sorter/stapler guide bar motor or guide bar motor sensor
C84 Sorter/stapler slide motor problem or sensor problem
C91 RADF original feed motor drive problem; motor, pulse sensor, etc
C92 RADF belt drive motor drive problem; motor pulse sensor, RADF main board
C93 RADF loop motor problem. Loop motor, pulse sensor or RADF main board.
OP Cover or door open
PF Paper feed
U1 Key counter missing
Коды ошибок копировальных аппаратов

Mita 2555
Code Description
C1 Back up battery
C2 Back up memory
C20 Drive
C31 Scan (Reset by unplugging)
C40 Lens motor
C50 Charge corona
C51 T/S corona
C60 High fuser temp.
C61 Heat problem or fuser switches
C62 Heat problem
C63 Low temperature
C70 DV selector
CO1 Back up battery
CO2 Back up memory
CO5 Drum thermistor
Коды ошибок копировальных аппаратов

Mita 2585
Code Description
C1 Back up battery
C2 Back up memory
C20 Drive
C31 Scan (Reset by unplugging)
C40 Lens motor
C50 Charge corona
C51 T/S corona
C60 High fuser temp.
C61 Heat problem or fuser switches
C62 Heat problem
C63 Low temperature
C70 DV selector
CO1 Back up battery
CO2 Back up memory
CO5 Drum thermistor
Коды ошибок копировальных аппаратов

Mita 3055
Code Description
C01 Memory loss, main board, etc. Do simulation 70.
C03 Communication problem between main board and scan, or bad scan board or main board.
C21 Main drive problem
C22 Desk side to side registration motor problem
C23 Desk drive problem
C31 Scan problem
C41 Lens problem
C51 Charge corona problem
C52 Transfer/separator corona problem
C61 Fuser problem. SSR
C63 Fuser thermistor
C64 Fuser temperature too high
C65 Fuser temperature too low
C71 Developer thermistor
C72 Drum thermistor open
C73 Drum thermistor short
OP Door open
U1 Key counter
Коды ошибок копировальных аппаратов

Mita 3060
Code Description
J020 Paper deck horizontal jam
J021 Paper deck horizontal jam
J022 Paper deck horizontal jam
J023 Converging section jam
J024 Multiple sheets in feed section
J025 Multiple sheets in vertical section
J026 Multiple sheets in duplex
J027 Multiple sheets before registration
J030 Registration or transfer area jam
J040 Fuser jam
J050 Exit jam
J051 Feed shift jam
J060 Duplex jam
J070 No original fed by RADF
J071 RADF jam
J072 RADF belt area jam
J073 RADF loop section jam
J074 RADF exit jam
J080 Copier to sorter jam
J081 Sorter feed in jam
J082 Jam in non sort bin
J083 Non sort exit jam
J084 Sorter conveyor jam
J085 Sorter exit jam
J090 Post sorter jam
J091 Stacker hand section jam
Коды ошибок копировальных аппаратов

Mita 312
Code Description
C1 Drive motor
C2 Blanking/cleaning lamp
C3 Lens problem
C4 Transfer/separator corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
C1 Drive motor
C2 Cleaning lamp / blanking lamps
C3 Lens
C4 Transfer/Separation corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
Коды ошибок копировальных аппаратов

Mita 312RE
Code Description
C1 Drive motor
C2 Cleaning lamp / blanking lamps
C3 Lens
C4 Transfer/Separation corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
Коды ошибок копировальных аппаратов

Mita 313Z
Code Description
C1 Scanner home problem, constant jams
C1 Scanner home problem/constant jams
C2 Motor, clockpulse
C2 Motor, clock pulse
C3 Scanner problems
C3 Scanner problem
C4 Exposure lamp
C4 Exposure lamp
C5 Blank lamp
C5 Blank lamp
C6 Coronas
C6 Coronas
C7 Heater
C7 Heater
C9 Lens motor
C9 Lens motor
CA Sorter
CA Sorter
CB Document feeder
CB Document feeder
C1 Frequent paper jams
C1 Frequent paper jams
C2 Drive motor/clock pulse
C2 Drive motor, clock pulse
C30 Scanner problem
C30 Scanner problem
C31 Exposure lamp
C31 Exposure lamp
C4 Lens motor
C4 Lens motor
C50 Corona Trans./Sep.
C50 Corona, transfer/separator
C51 Main corona
C51 Main Corona
C6 Heater problem
C6 Heater problem
C7 Blanking lamp
C7 Blanking lamp
C8 Sorter
C8 Sorter
C9 Document feeder
C9 Document feeder
Коды ошибок копировальных аппаратов

Mita 313ZD
Code Description
C1 Frequent paper jams
C1 Frequent paper jams
C2 Drive motor/clock pulse
C2 Drive motor, clock pulse
C30 Scanner problem
C30 Scanner problem
C31 Exposure lamp
C31 Exposure lamp
C4 Lens motor
C4 Lens motor
C50 Corona Trans./Sep.
C50 Corona, transfer/separator
C51 Main corona
C51 Main Corona
C6 Heater problem
C6 Heater problem
C7 Blanking lamp
C7 Blanking lamp
C8 Sorter
C8 Sorter
C9 Document feeder
C9 Document feeder
Коды ошибок копировальных аппаратов

Mita 3285
Code Description
30 Exposure lamp/XL thermofuse
32 Exposure lamp stays on
C1 Back up battery
C2 Back up memory
C20 Drive
C31 Scan (Reset by unplugging)
C40 Lens motor
C50 Charge corona
C51 T/S corona
C60 High fuser temp
C61 Heat prob./fuser switch
C62 Heat problem
C63 Low temperature
C70 DV selector
CO1 Back up battery
CO2 Back up memory
CO5 Drum thermistor
Коды ошибок копировальных аппаратов

Mita 3555
Code Description
C01 Battery on main board
C02 Battery on main board. May be reset with simulation 70
C05 Drum thermistor. May be reset with simulation 49
C20 Drive problem (pulse sensor, broken gear, bind etc.)
C21 Side registration motor or switch problem (duplex area?)
C30 Exposure lamp problem or Auto exposure sensor
C31 Scan problem
C40 Lens motor problem
C41 Mirror motor problem
C50 Charge corona
C51 Transfer/separator corona
C60 High fuser temperature, or shorter thermistor
C61 Open thermistor
C62 Open heater lamp. Not sure if this code would light for open thermosfuse or low heat
Коды ошибок копировальных аппаратов

Mita 3585
Code Description
C01 Battery on main board
C02 Battery on main board. May be reset with simulation 70
C05 Drum thermistor. May be reset with simulation 49
C20 Drive problem (pulse sensor, broken gear, bind etc.)
C21 Side registration motor or switch problem (duplex area?)
C30 Exposure lamp problem or Auto exposure sensor
C31 Scan problem
C40 Lens motor problem
C41 Mirror motor problem
C50 Charge corona
C51 Transfer/separator corona
C60 High fuser temperature, or shorter thermistor
C61 Open thermistor
C62 Open heater lamp. Not sure if this code would light for open thermosfuse or low heat
Коды ошибок копировальных аппаратов

Mita 3755
Code Description
C01 Battery problem. Try simulation 70
C02 Battery problem. Try simulation 70
C03 Serial communication (main board)
C05 Drum thermistor
C20 Drive problem
C21 Side to side switch in duplex unit
C22 Suction fan
C30 Exposure lamp
C31 Scan drive
C40 Lens drive
C41 Mirror drive
C50 Charge corona
C51 Transfer/separator corona
C60 High fuser temperature
C61 Open fuser thermistor
C62 Low fuser temperature
Коды ошибок копировальных аппаратов

Mita 3785
Code Description
C01 Battery problem. Try simulation 70
C02 Battery problem. Try simulation 70
C03 Serial communication (main board)
C05 Drum thermistor
C20 Drive problem
C21 Side to side switch in duplex unit
C22 Suction fan
C30 Exposure lamp
C31 Scan drive
C40 Lens drive
C41 Mirror drive
C50 Charge corona
C51 Transfer/separator corona
C60 High fuser temperature
C61 Open fuser thermistor
C62 Low fuser temperature
Коды ошибок копировальных аппаратов

Mita 4056
Code Description
C01 Memory problem. Use simulation 70
C03 Communication problem between main board and scan board
C05 Auxiliary CPU ROM on main board
C21 Main drive problem
C22 Duplex side to side registration motor problem
C23 Desk drive problem
C24 Suction motor
C31 Scan problem
C41 Lens problem
C51 Charge corona short
C52 Transfer/separator corona short
C61 Fuser problem. Low temperature or open circuit
C63 Fuser problem. Thermistor
C64 Fuser problem. High temperature
C65 Fuser problem. Low temperature or open circuit
C72 Drum thermistor open
C73 Drum thermistor shorted
C74 Developer unit thermistor open
C81 Sorter paper feed motor
C82 Sorter bin motor
C83 Stapler jam
C84 Sort bin problem
C85 Sorter table motor
C86 Sorter bin slide motor
C87 Sorter paperweight motor
C88 Sorter jogger motor
C89 Punch jam
C91 RADF feed motor
C92 RADF transport motor
C93 RADF loop motor
C94 RADF motor running too fast
C95 RADF loop motor running too fast
Коды ошибок копировальных аппаратов

Mita 4085
Code Description
C2 Drive
C30 Scan
C31 Exposure lamp
C4 Lens motor
C50 T/S corona
C51 Charge corona
C60 Thermistor
C61 Heater
C7 Blank lamp
C8 Sorter
Коды ошибок копировальных аппаратов

Mita 4086
Code Description
C01 Memory problem. Use simulation 70
C03 Communication problem between main board and scan board
C05 Auxiliary CPU ROM on main board
C21 Main drive problem
C22 Duplex side to side registration motor problem
C23 Desk drive problem
C24 Suction motor
C31 Scan problem
C41 Lens problem
C51 Charge corona short
C52 Transfer/separator corona short
C61 Fuser problem. Low temperature or open circuit
C63 Fuser problem. Thermistor
C64 Fuser problem. High temperature
C65 Fuser problem. Low temperature or open circuit
C72 Drum thermistor open
C73 Drum thermistor shorted
C74 Developer unit thermistor open
C81 Sorter paper feed motor
C82 Sorter bin motor
C83 Stapler jam
C84 Sort bin problem
C85 Sorter table motor
C86 Sorter bin slide motor
C87 Sorter paperweight motor
C88 Sorter jogger motor
C89 Punch jam
C91 RADF feed motor
C92 RADF transport motor
C93 RADF loop motor
C94 RADF motor running too fast
C95 RADF loop motor running too fast
Коды ошибок копировальных аппаратов

Mita 4090
Code Description
J020 Paper deck horizontal jam
J021 Paper deck horizontal jam
J022 Paper deck horizontal jam
J023 Converging section jam
J024 Multiple sheets in feed section
J025 Multiple sheets in vertical section
J026 Multiple sheets in duplex
J027 Multiple sheets before registration
J030 Registration or transfer area jam
J040 Fuser jam
J050 Exit jam
J060 Duplex jam
J070 No original fed by RADF
J071 RADF jam
J072 RADF belt area jam
J073 RADF loop section jam
J074 RADF exit jam
J080 Copier to sorter jam
J081 Sorter feed in jam
J082 Jam in non sort bin
J083 Non sort exit jam
J084 Sorter conveyor jam
J085 Sorter exit jam
J090 Post sorter jam
J091 Stacker hand section jam
Коды ошибок копировальных аппаратов

Mita 412
Code Description
C1 Drive motor
C2 Blanking/cleaning lamp
C3 Lens problem
C4 Transfer/separator corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
C1 Drive motor
C2 Cleaning lamp / blanking lamps
C3 Lens
C4 Transfer/Separation corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
Коды ошибок копировальных аппаратов

Mita 412RE
Code Description
C1 Drive motor
C2 Cleaning lamp / blanking lamps
C3 Lens
C4 Transfer/Separation corona
C5 Scanner
C6 Exposure lamp
C7 Thermistor
C8 Heat
Коды ошибок копировальных аппаратов

Mita 4555
Code Description
C01 Battery
C02 Memory
C03 Main board or eject board
C05 Drum thermistor
C20 Drive
C21 Duplex side to side registration motor/switches
C30 Exposure lamp/thermofuse
C31 Scan
C40 Lens motor
C41 Mirror motor
C50 Charge corona
C51 Transfer/separator
C60 High fuser temperature
C61 Fuser thermistor
C62 Low temperature
Коды ошибок копировальных аппаратов

Mita 4585
Code Description
C01 Battery
C02 Memory
C03 Main board or eject board
C05 Drum thermistor
C20 Drive
C21 Duplex side to side registration motor/switches
C30 Exposure lamp/thermofuse
C31 Scan
C40 Lens motor
C41 Mirror motor
C50 Charge corona
C51 Transfer/separator
C60 High fuser temperature
C61 Fuser thermistor
C62 Low temperature
Коды ошибок копировальных аппаратов

Mita 4655
Code Description
C01 Battery problem. Try simulation 70
C02 Battery problem. Try simulation 70
C03 Serial communication (main board)
C05 Drum thermistor
C20 Drive problem
C21 Side to side switch in duplex unit
C22 Suction fan
C30 Exposure lamp
C31 Scan drive
C40 Lens drive
C41 Mirror drive
C50 Charge corona
C51 Transfer/separator corona
C60 High fuser temperature
C61 Open fuser thermistor
C62 Low fuser temperature
Коды ошибок копировальных аппаратов

Mita 4685
Code Description
C01 Battery problem. Try simulation 70
C01 Backup battery problem--With the main switch on, the back up battery voltage is lower than 2.8V.
C02 Backup memory problem--Backup memory is faulty.
C02 Battery problem. Try simulation 70
C03 Serial communication (main board)
Serial communication problem--Less than 10 serial data signals are input into and output from the
C03
main PCB every 50ms.
Drum thermistor problem--The drum thermistor output voltage is out of the range between 0.3 and
C05
4.7V
C05 Drum thermistor
Drive problem--More than 20 clock pulses are not input to the main PCB within 1 s after the drive
C20
motor has turned on.
C20 Drive problem
C21 Side to side switch in duplex unit
Side registration motor problem--The side registration switch fails to turn on within 8 s after the main
C21
switch has turned on.
C22 Suction fan
C22 Paper conveying section fan motor problem--CN1-5 on the BM detection PCB remains high.
C30 Exposure lamp
Broken halogen lamp wire--The AE sensor output does not exceed 4 V within 300 ms after the HL
C30
REMOTE signal has applied to the AVR/Output PCB.
C31 Scan drive
C40 Lens drive
Lens motor problem--The lens home position switch fails to turn on within 8 s after the main switch
C40
has turned on.
Mirror motor problem--The mirror home position switch fails to turn on within 8 s after the main switch
C41
has turned on.
C41 Mirror drive
C50 Main high voltage problem.
C50 Charge corona
C51 Transfer, separation high voltage problem.
C51 Transfer/separator corona
C60 High fuser temperature
Abnormally high temperature in the fixing section--The fixing unit thermistor output voltage remains
C60
less than 0.5 V for longer than 1 s, indicating the fixing temperature rises above 536F.
C61 Open fuser thermistor
Broken fixing unit thermistor wire--The fixing unit thermistor wire--The fixing unit thermistor output
C61
voltage exceeds 4.9 V.
Broken fixing unit heater wire--Fixing temperature does not reach 329 F within 4 minutes after the
C62
power relay has turned on.
C62 Low fuser temperature
Коды ошибок копировальных аппаратов

Mita 513Z
Code Description
C01 Toner sensor
C02 Drum heater
C03 Drum heater
C04 Toner sensor
C05 Data transfer
C06 Board problem
C07 Board problem
C21 Drive motor/clock pulse
C22 PF motor/clock pulse
C31 Exposure lamp stays off
C32 Exposure lamp stays on
C35 Serve motor board/scan motor
C36 Serve motor/clock pulse
C37 Scan drive
C41 Lens motor
C51 Charge corona
C52 Transfer/sep/corona
C53 Bias below 125VDC
C55 Drum potential
C56 Drum potential
C58 Drum potential
C61 Heater M off
C62 Heater M on
C63 Heater S off
C64 Heater S on
C65 Thermistor
C66 Thermistor
C71 Blank lamp/cleaning lamp
Коды ошибок копировальных аппаратов

Mita 5555
Code Description
C05 Communication problem between main boards
C06 Battery/memory problem
C21 Main motor drive
C22 Duplex motor drive
C23 Paper feed motor drive
C24 Duplex motor drive
C25 Paper feed motor drive
C31 Open exposure lamp
C32 Exposure lamp stays on
C35 Scan motor or scan motor board or fuser
C37 Scan sensor not actuated or not deactuated at proper time
C41 Lens motor
C51 Charge corona
C52 Transfer/separator corona
C53 Bias is less then 100 volts
C55 Drum surface voltage is too high
C56 Drum surface voltage is too low
C61 Fuser lamp closest to exit end stays off
C62 Fuser lamp closest to drum stays off
C63 Fuser lamp(s) stays on
C65 High fuser temperature
C66 Open fuser thermistor
C71 Blank lamp problem
C72 Drum thermistor shorted
C73 Drum thermistor open
C74 High DV unit temperature or shorted DV thermistor
C75 Open DV thermistor
Коды ошибок копировальных аппаратов

Mita 5585
Code Description
C05 Communication problem between main boards
C06 Battery/memory problem
C21 Main motor drive
C22 Duplex motor drive
C23 Paper feed motor drive
C24 Duplex motor drive
C25 Paper feed motor drive
C31 Open exposure lamp
C32 Exposure lamp stays on
C35 Scan motor or scan motor board or fuser
C37 Scan sensor not actuated or not deactuated at proper time
C41 Lens motor
C51 Charge corona
C52 Transfer/separator corona
C53 Bias is less then 100 volts
C55 Drum surface voltage is too high
C56 Drum surface voltage is too low
C61 Fuser lamp closest to exit end stays off
C62 Fuser lamp closest to drum stays off
C63 Fuser lamp(s) stays on
C65 High fuser temperature
C66 Open fuser thermistor
C71 Blank lamp problem
C72 Drum thermistor shorted
C73 Drum thermistor open
C74 High DV unit temperature or shorted DV thermistor
C75 Open DV thermistor
Коды ошибок копировальных аппаратов

Mita 5685
Code Description
C05 Circuit board problem
C06 Battery problem. Try simulation 79
C07 Ram problem
C21 Drive problem-upper section
C22 Drive problem-lower section
C23 Paper feed motor
C24 Duplex side registration sensor (jogger) or motor
C25 Large capacity cassette
C26 Fuser motor
C31 Open exposure lamp
C32 Exposure lamp won t shut off
C35 Scan motor scan board
C41 Lens motor
C51 Charge corona
C52 Transfer/separator corona
C53 Bias problem
C54 Drum potential sensor
C55 Drum potential sensor
C56 Drum potential sensor or no charge
C62 Fuser problem. Low heat. Lamp (there are 2) or thermofuse
C63 Fuser lamps won’t shut off
C65 High fuser temperature or shorted fuser thermistor
C66 Open fuser thermistor
C71 Blank lamp problem
C72 Shorted drum thermistor
C73 Shorted DV unit thermistor
C74 Shorted DV unit thermistor
C75 Open DV unit thermistor
Коды ошибок копировальных аппаратов

Mita 6090
Code Description
C010 Backup memory problem--The specified data was not written into NVRAM.
Serial communication problem (main PCB problem)--Communication procedure fails to complete
C030
within 200 ms in any block. Nine consecutive reception errors occur in one block.
Serial communication problem (operation unit PCB problem)--Communication procedure fails to
C031
complete within 200 ms in any block. Nine consecutive reception errors occur in one block.
Serial communication problem (servo motor PCB problem)--serial communication between the main
C032
PCB and the servo motor PCB fails five times consecutively.
Serial communication problem (RDH main PCB problem)--Serial communication between the copier
C033
main PCB and the RDH main PCB fails five times consecutively.
Halogen lamp problem--While the scanner motor rotates in forward direction because of the lamp on
C110 signal, the HLISENS input signal fails to go low. The HLISENS input signal fails to go low during
exposure correction.
Paper conveying motor problem--No encoder signal is received 250 ms after the paper conveying
C210
motor on signal has been emitted.
Side registration motor problem--The side registration home position switch fails to turn on within 5 s
C220
after the main switch has been turned on.
Fewer than five pulses are generated by the drum motor encoder in 1 s after the drum motor on
C230
signal has been emitted.
Paper deck motor problem--The paper deck level switch or the home position switch fails to turn on
C240
within 20 s after the paper deck motor on signal has been emitted.
Upper drawer motor problem--The upper drawer level switch or the position switch fails to turn on
C250
within 8 s
Middle drawer motor problem--The middle drawer level switch or the position switch fails to turn on
C251
within 8 s after the middle drawer motor on signal has been emitted.
Lower drawer motor problem--The lower drawer level switch or the position switch fails to turn on
C252
within 8 s after the middle drawer motor on signal has been emitted.
Scanner motor problem (main PCB problem)--The home position switch fails to turn on within 4 s
C310
after the scanner motor reverse signal has been emitted.
Scanner motor problem (servo motor PCB problem)--No signal is generated by the encoder 20ms
C311
after the scanner motor reverse signal has been emitted.
Scanner motor problem3523 or more SM forward pulses are received after the scanner motor has
C312
started to rotate forward. The scanner motor speed exceeds the specified level.
C313 The home position switch fails to turn on within 4 s after the SM HP signal has gone low.
Servo motor CPU problem--With the scanner motor forward signal on, the average motor speed
exceeds 900 mm/s in any 60 ms (excluding the first 20 ms after the signal is emitted;or with the
C314
scanner motor reverse signal on, the average motor speed exceeds 1600 mm/s in any 60 ms
excluding the first 60 ms after the signal is emitted.
Lens motor problem--The lens home position switch fails to turn on within 12 s after the lens motor
C410
home signal has been emitted.
Main high voltage problem--The short detection signal is generated by the main charger high-voltage
C510
PCB for 5 s.
Transfer high voltage problem--The transfer high voltage short detection signal is generated by the
C520
transfer charger high-voltage PCB for 5 s.
Separation high-voltage problem--The separation high voltage short detection signal is generated by
C521
the transfer charger high-voltage PCB for 5 s.
Pre-transfer high-voltage problem--The pre-transfer short detection signal is generated by the
C530
pretransfer charger high-voltage PCB for 5 s.
C540 Bias problem-The short detection signal is generated by the bias PCB for 5 s.
Potential sensor problem--During initial potential sensor calibration, the difference between the
C550
sensor outputs when 500 V and 300 V are applied to the drum is zero or negative.
Potential adjustment problem: max level--During initial potential settling, the drum potential cannot be
C560
set to the specified level by increasing the primary main charger control signal to its maximum.
Potential adjustment problem: min. level--During initial potential setting, the drum potential cannot be
C561
set to the specified level by reducing the primary admin charger control signal to its minimum.
C570 Exposure adjustment problem: max level--
Exposure adjustment problem: min level--During initial light intensity correction, the potential sensor
C571
output cannot be set to the specified level even with the halogen lamp control signal at min.
Fixing unit heater M wire broken--No heater check signal is generated by the noise filter PCB 800 ms
C610
after the fixing unit heater S off signal and the fixing unit heater M on signal have been emitted.
Fixing unit heater S wire broken--No heater check signal is generated by the noise filter PCB 800 ms
C611
after the fixing unit heater M off signal and the fixing unit heater S on signal have been emitted.
Fixing unit heats failing to turn off--The heater check signal continues to be generated by the noise
C620
filter PCB 320 ms after the fixing unit heater M and S off signals have been emitted.
Fixing unit thermistor wire broken--The data generated by the fixing unit thermistor remains at F1H or
C630
above for longer than two minutes while fixing unit heaters M and S are on.
Fixing unit thermistor wire shorted/abnormally high temperature detected--Data from the fixing unit
C640
thermistor remains at 45H or less for 160 ms or longer.
Fixing unit thermistor abnormally low temperature detected--The signal from the fixing unit thermistor
C641
registers 100C or lower during standby or a copying cycle after secondary stabilization.
Toner sensor problem--Data from the toner sensor remains at 14H or less, or F0H or above for 320
C710
ms.
C720 Drum thermistor wire broken--The signal from the drum thermistor remains high for 5 s.
Drum thermistor shorted/abnormally high temperature detected--The signal from the drum thermistor
C730
remains low for 5 s.
Drum thermistor abnormally low temperature detected--The drum heater remains on at 100% output
C731
for 17 minutes with the safety switches on.
Internal temperature thermistor broken--Data from the internal temperature thermistor remains at
C740
0CH or less for 320 ms.
External temperature thermistor problem--Data from the external temperature thermistor remains at
C741 F0H or above (too low a temperature or broken wire) or at 33H or less (too high a temperature or
shorted wire) for 320 ms.
Developing unit thermistor problem--Data from the developing unit thermistor remains at F0H or
C750 above (too low a temperature or broken wire) or at 33H or less (too high a temperature or shorted
wire) for 320 ms.
Toner cartridge shutter problem--The shutter home position switch fails to turn off within 10 s after the
C760 toner cartridge a shutter mode on signal has been emitted. The shutter home position switch fails to
turn on within 40 s after it has turned off.
Toner cartridge loading problem--The TCPSW1 or TCPSW2 signal falls to be input within 40 s after
C761
the toner cartridge loading motor on signal has been emitted.
Toner hopper problem--No signal is input from the toner level detection switch after automatic toner
C762
replenishing is completed.
Sorter feed motor problem--A feed motor problem--A feed motor jam is detected (with the
C810
stapler-sorter attached). The feed motor current exceeds 2 A for 50 ms (with the sorter attached).
Sorter feed motor circuit problem--No feed motor index signal is detected for 30 ms (with the sorter
C811
attached).
Sorter bin drive motor problem--The sorter bin unit fails to return to the home position during
C820 initialization (with the stapler-sorter attached). The sorter shift motor current exceeds 1.2 A for 50 ms
(with the sorter attached).
Sorter shift motor PCB problem (sorter)--No encoder signal is detected from the sorter shift motor for
C821
50 ms.
Sorter table motor problem (stapler-sorter)--The sorters stapler table fails to return to the home
C830
position during initialization.
Sorter bin side motor problem (stapler-sorter)--The bin fails to return to the sliding home position
C831 during initialization. The bin fails to move to the stapling/punching position. The bin fails to return to
the sliding home position.
Sorter paper weight motor problem (stapler-sorter)--The sorter paper weight fails to return to the
C832 home position during initialization. The sorter paper weight fails to move to the operating position
when it should. The sorter paper weight fails to return to the home position after releasing the paper.
Sorter jog motor problem--The jog unit fails to return to the home position during initialization. The job
C833
unit fails to move to the standby position when paper is fed.
Sorter bin upper limit detected (stapler-sorter)--The bin upper limit sensor turns on while the sorter bin
C840
drive motor drives.
Sorter bin unit lower limit detected (stapler-sorter)--The bin unit lower limit sensor turns on while the
C841

<<

стр. 5
(всего 13)

СОДЕРЖАНИЕ

>>