<<

стр. 9
(всего 13)

СОДЕРЖАНИЕ

>>

51 Door open
61 Document feeder open
62 Document feeder jam
63 Document feeder exit jam
64 Document feeder original did not exit
71 Sort jam
72 Sort door open
72 Sort exit jam
11 Paper feed jam
12 Paper feed jam
21 Separator jam
22 Separator jam
31 Exit jam
32 Exit jam
41 Optics problem
51 Door open
61 Document feeder open
62 Document feeder jam
63 Document feeder exit jam
64 Document feeder original did not exit
71 Sort jam
72 Sort door open
72 Sort exit jam
Коды ошибок копировальных аппаратов

Royal 130R
Code Description
11 Paper feed jam
12 Paper feed jam
21 Separator jam
22 Separator jam
31 Exit jam
32 Exit jam
41 Optics problem
51 Door open
61 Document feeder open
62 Document feeder jam
63 Document feeder exit jam
64 Document feeder original did not exit
71 Sort jam
72 Sort door open
72 Sort exit jam
Коды ошибок копировальных аппаратов

Royal 1602
Code Description
11 Jam in upper cassette
12 Jam in lower cassette
13 Jam in optional cassette
14 Jam
21 Separator jam
32 Conveyor jam
41 Optical unit
42 Optical unit
43 CVR problem (ex. Lamp/Bd.)
44 Optical unit
45 Lens unit
46 Lens unit
51 Door open
52 Drive
71 Sorter lid open
72 Sorter
81 No key counter
Коды ошибок копировальных аппаратов

Royal 2502
Code Description
11 Jam in upper cassette
12 Jam in lower cassette
13 Jam in optional cassette
14 Jam
21 Separator jam
32 Conveyor jam
41 Optical unit
42 Optical unit
43 CVR problem (ex. Lamp/Bd.)
44 Optical unit
45 Lens unit
46 Lens unit
51 Door open
52 Drive
71 Sorter lid open
72 Sorter
81 No key counter
Коды ошибок копировальных аппаратов

Royal 3302
Code Description
41 Optics
51 Front door open
61 Document feeder open
81 Key counter out
Коды ошибок копировальных аппаратов

Sanyo 1100
Sanyo 1102
Sanyo 115
Sanyo 1150
Sanyo 1152
Sanyo 116
Sanyo 120
Sanyo 122
Sanyo 125 Sanyo 870
Sanyo 133 Sanyo 90
Sanyo 50 Sanyo Z-80
Sanyo 50L
Sanyo 600
Sanyo 605
Sanyo 70
Sanyo 800
Sanyo 802
Sanyo 850
Sanyo 852
Коды ошибок копировальных аппаратов

Sanyo 1100
Code Description
H2 Main drive malfunction, sensor board
H2 Main drive malfunction or sensor board
H4 No 24VDC (or less than 18VDC)
H4 24V problem
H6 Optical lens unit
H6 Optical lens unit or sensor board
H8 Cleaning system malfunction
H8 Cleaning system malfunction
Коды ошибок копировальных аппаратов

Sanyo 1102
Code Description
H2 Main drive malfunction, sensor board
H2 Main drive malfunction or sensor board
H4 No 24VDC (or less than 18VDC)
H4 24V problem
H6 Optical lens unit
H6 Optical lens unit or sensor board
H8 Cleaning system malfunction
H8 Cleaning system malfunction
Коды ошибок копировальных аппаратов

Sanyo 115
Code Description
E1 Scan not home
E2 Scan did not reach reg. Switch
E3 DC motor overload
E4 Scan speed error
E5 No scan return
H2 Drive
H3 Low temperature
H4 No 24V
H6 Lens
H8 Cleaning unit
H2 Main drive malfunction or sensor board
H2 Main drive malfunction, sensor board
H4 No 24VDC (or less than 18VDC)
H4 24V problem
H6 Optical lens unit
H6 Optical lens unit or sensor board
H8 Cleaning system malfunction
H8 Cleaning system malfunction
H2 Main drive malfunction or sensor board
H2 Main drive malfunction, sensor board
H4 24V problem
H4 No 24VDC (or less than 18VDC)
H6 Optical lens unit or sensor board
H6 Optical lens unit
H8 Cleaning system malfunction
H8 Cleaning system malfunction
Коды ошибок копировальных аппаратов

Sanyo 1150
Code Description
H2 Main drive malfunction, sensor board
H2 Main drive malfunction or sensor board
H4 No 24VDC (or less than 18VDC)
H4 24V problem
H6 Optical lens unit
H6 Optical lens unit or sensor board
H8 Cleaning system malfunction
H8 Cleaning system malfunction
Коды ошибок копировальных аппаратов

Sanyo 1152
Code Description
H2 Main drive malfunction, sensor board
H2 Main drive malfunction or sensor board
H4 No 24VDC (or less than 18VDC)
H4 24V problem
H6 Optical lens unit
H6 Optical lens unit or sensor board
H8 Cleaning system malfunction
H8 Cleaning system malfunction
Коды ошибок копировальных аппаратов

Sanyo 116
Code Description
E1 Scan not home
E2 Scan did not reach reg. Switch
E3 DC motor overload
E4 Scan speed error
E5 No scan return
H2 Drive
H3 Low temperature
H4 No 24V
H6 Lens
H8 Cleaning unit
Коды ошибок копировальных аппаратов

Sanyo 120
Code Description
H1 High temperature
H11 Mirror home/not home
H12 Mirror
H14 Mirror motor speed
H15 No mirror return
H3 Low temperature
H4 24V problem
H6 Lens
J0 PF jam
J1 Registration jam
J2 Transport jam
J3 Fuser jam
J4 Separator area jam
Коды ошибок копировальных аппаратов

Sanyo 122
Code Description
H1 High temperature
H11 Mirror not home
H12 Scan problem
H13 Mirror motor speed
H14 Mirror motor speed
H15 No mirror return
H3 Low temperature
H4 Low 24V
H5 Side erase shutter not home
H6 Lens not home
H7 Under toned
H9 No power to toner sensor
J0 PF jam
J1 Registration jam
J2 Transport jam
J3 Fuser jam
Коды ошибок копировальных аппаратов

Sanyo 125
Code Description
Ba Battery problem
CL Door interlock
H1 high fuser temperature
H16 Total counter unplugged, or 24 volt problem
H3 Low fuser temperature
H6 Lens home problem
H8 Scan problem
HA Doc. Feeder interface to copier
J0 Feed jam
J1 Internal jam
J3 Internal or exit jam
J4 Jam in drum area
J8 Jam in document feeder
PE Paper empty
Коды ошибок копировальных аппаратов

Sanyo 133
Code Description
H1 High fuser temperature
H11 Mirror not home
H12 Scan problem
H15 Mirror return problem
H3 Low fuser temperature
H4 Low 24 volts
H6 Lens not home
J1 Registration jam
J10 Paper feed jam
J2 Transport jam
J3 Fuser jam
J4 Jam in cleaner unit
J5 Jam in ADF or optional cassette attachment
J6 Jam in ADF or optional cassette attachment
JA Jam in ADF or optional cassette attachment
Коды ошибок копировальных аппаратов

Sanyo 50
Code Description
C Developer/toner cartridge is not in right or door is open
E 20,000 copies have been run and machine should go to shop for drum replacement
H1 High fuser temperature
H2 Scan problem
H3 Low fuser temperature
H5 Exposure lamp problem
P Add paper
C Developer/toner cartridge is not in right or door is open
E 20,000 copies have been run and machine should go to shop for drum replacement
H1 High fuser temperature
H2 Scan problem
H3 Low fuser temperature
H5 Exposure lamp problem
P Add paper
Коды ошибок копировальных аппаратов

Sanyo 50L
Code Description
C Developer/toner cartridge is not in right or door is open
E 20,000 copies have been run and machine should go to shop for drum replacement
H1 High fuser temperature
H2 Scan problem
H3 Low fuser temperature
H5 Exposure lamp problem
P Add paper
Коды ошибок копировальных аппаратов

Sanyo 600
Code Description
H2 Scanner fuser
H3 Fuser
Коды ошибок копировальных аппаратов

Sanyo 605
Code Description
H2 Scanner fuser
H3 Fuser
Коды ошибок копировальных аппаратов

Sanyo 70
Code Description
E1 Scan not home
E2 Scan
H1 High temperature
H3 Low temperature
J0 Feed jam
J1 Registration jam
J2 Transport jam
J3 Fuser jam
Коды ошибок копировальных аппаратов

Sanyo 800
Code Description
H2 Drive
H2 Drive
H4 24V problem or fuse
H4 check 24v and fuse
Коды ошибок копировальных аппаратов

Sanyo 802
Code Description
H2 Drive
H4 24V problem or fuse
Коды ошибок копировальных аппаратов

Sanyo 850
Code Description
H2 Drive
H4 24V problem or fuse
Коды ошибок копировальных аппаратов

Sanyo 852
Code Description
H2 Drive
H4 24V problem or fuse
Коды ошибок копировальных аппаратов

Sanyo 870
Code Description
H2 Drive
H4 check 24v and fuse
Коды ошибок копировальных аппаратов

Sanyo 90
Code Description
Ba Battery problem
CL Door interlock
H1 high fuser temperature
H16 Total counter unplugged, or 24 volt problem
H3 Low fuser temperature
H6 Lens home problem
H8 Scan problem
HA Doc. Feeder interface to copier
J0 Feed jam
J1 Internal jam
J3 Internal or exit jam
J4 Jam in drum area
J8 Jam in document feeder
PE Paper empty
Коды ошибок копировальных аппаратов

Sanyo Z-80
Code Description
bA Battery problem
CL Interlock
H1 Fuser temperature too high
H3 Fuser temperature too low
H6 Lens home problem
H7 Mirror home problem
H8 Scan home problem
J0 Feed jam
J1 Internal jam
J3 Exit jam
P1 Internal jam
PE Paper empty
Коды ошибок копировальных аппаратов

Savin v-35
Code Description
00 If this displays at turn on; shorted sensor
1 Relay roller area
3 Separator area
4 Exit area
5 Sorter
6 Duplex area
7 Third feed roller
Sort area during duplex: Examples; 04 would indicate that the paper did not reach exit switch. 23
8
would indicate that the separator switch stayed actuated.
E41 Upper lift sensor
E43 Lower lift sensor
E44 Third lift sensor
E53 Open fuser thermistor or no warm up
E54 Low temperature
E55 High temperature
E57 High temperature
E61 Pulse generator, Drive problem
E81 Jogger problem
E91 Counter
E93 Main board
U11 Add toner light has been on for 99 copies
U12 Add dispersant light has been on for 99 copies
U13 Too much dispersant. Will not add toner
U21 More than 15 11 x 17 copies or 30 8 1/2 x 11
U22 All bins have been used in group
U41 Color selected and too much dispersant
U42 Color selected and add dispersant lit
U45 Color selected and too much dispersant
U46 Low color dispersant
U51 Transport down
U52 Console door
U53 Duplex transport
U54 Sorter cover
U55 Paper misaligned in bypass
Коды ошибок копировальных аппаратов

Sharp 1430 Sharp 8260
Sharp 2020 Sharp 830
Sharp 2022 Sharp 8300
Sharp 2025 Sharp 835
Sharp 2027 Sharp 8350
Sharp 2030 Sharp 8400
Sharp 2035 Sharp 845
Sharp 2040 Sharp 850
Sharp 2050 Sharp 8600
Sharp 2114 Sharp 8875
Sharp 2116 Sharp 900
Sharp 2118 Sharp 901
Sharp 2120 Sharp 9300
Sharp 2214 Sharp 9500
Sharp 2216 Sharp 9550
Sharp 2414 Sharp 9700
Sharp 2514 Sharp 9750
Sharp 7100 Sharp ALL
Sharp 7200 Sharp ALL MODELS
Sharp SF-2014
Sharp 7320
Sharp SF2314
Sharp 7370
Sharp SN-1420
Sharp 750
Sharp Z50
Sharp 755
Sharp Z55
Sharp 756
Sharp Z60
Sharp 760
Sharp Z-60
Sharp 770
Sharp Z70
Sharp 7700
Sharp Z-800
Sharp 771
Sharp Z810
Sharp 7750
Sharp 780
Sharp 7800
Sharp 781
Sharp 7850
Sharp 7900
Sharp 810
Sharp 8100
Sharp 811
Sharp 815
Sharp 816
Sharp 820
Sharp 8200
Sharp 825
Sharp 826
Коды ошибок копировальных аппаратов

Sharp 1430
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp 2020
Code Description
CC Original detection problem
CH Lit Steadily: Sorter not installed, or not turned on
CH Flashing: DV unit not installed, not connected properly, or not latched in place properly
Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport
F1
motor drive.
Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark
F2
sensor problem. . Does not see mark on drum or sensor not working properly.
H2 Sub code 00: Fuser thermistor open.
H3 Sub code 00: Fuser temperature too high.
H4 Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.
L1 Scan forward problem. Motor, sensor, board
L3 Scan forward problem. Motor, sensor, board.
L4 Drive problem; main motor, gear, sensor, bind.
L5 Lens problem. Motor sensor board.
L8 Sub code 01: Zero cross.
P Paper feed problem or no paper
PC Card counter not installed
U2 Sub code 01: Memory loss.
U4 Sub code 00: Communication problem between copier and duplex unit.
U5 Sub code 00: Communication problem between main board and ADF.
Коды ошибок копировальных аппаратов

Sharp 2022
Code Description
P10 Set or clear departmental counter
P11 Display individual departmental counts
P13 Clear departmental counters
P14 Enter, clear or change department numbers
P16 Change max. number of copies that can be run
P18 Sends alarm if the wrong department number is tried three times in a row
P19 Change code number
P20 Adjust auto exposure
P21 Adjust automautic shufoff
P22 Adjust manual exposure
P23 Adjust auto clear time
P24 Set up fixed magnification settings
P25 Set maximum number of copies or of sets
P26 Binding margin
P27 Border erase setting
P28 Defaults at power on
P29 Display various counts
P30 Auto repeat on or off
P45 Message display time
P70 Auto paper select on or off
P71 Auto cassette select on or off
P72 Maximum copies in duplex
P73 Copy condition in rewrite
P74 Duplex limit when problems with duplex unit
P75 Prevent auto duplex
P76 Prevent stapling
P77 Prevent cover use
P90 List programs
Коды ошибок копировальных аппаратов

Sharp 2025
Code Description
C2 Transfer corona problem or HVT
CC Original detection problem.
CH Door open or developer unit not installed, not connected properly, or not latched in place properly.
Sub code 00: Communication error between main board and sorter. 01: Jogger error. 02: Sorter
F1
transport motor drive. 04: Sorter bin sensor problem. Lower limit sensed wrong.
Sub code 02: Toner motor problem. 31: Image density sensor problem. Could be a problem with the
F2 light level. 32: Drum mark sensor problem. Does not see mark on drum or sensor does not work
properly. 35: Grid voltage correction will not work during simulation.
F3 Sub code 12: Copier upper cassette lift motor problem. Copier bottom cassette lift motor problem.
H2 Fuser thermistor open.
H3 Fuser temperature too high.
H4 Fuser temperature too low. Lamp, thermal switch, connections.
L4 Sub code 01: Drive problem, main motor, sensor, bind.
L5 Sub code 03: Drive problem with 4th/5th mirror assembly, motor, sensor, board.
L8 Sub code 01: Power frequency problem.
PC Card counter or key counter not installed.
PF There is an inhibit command from the PC modem. This is reset with simulation 17.
U2 Sub code 00 or 01: Memory error.
U3 Sub code 20: Mirror motor locked. 21: Mirror motor home sensor.
U4 Sub code 02: Duplex alignment plate out of position motor, cable, sensor.
Sub code 00: Communication problem between main board and RADF. 01: RADF motor drive
U5
problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor.
Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive
U6
problem. 08: Desk 24v problem. 09: LCT motor overload. 10: Desk transport motor drive problem.
U7 Sub code 00: Communication problem between copier and PC modem.
Коды ошибок копировальных аппаратов

Sharp 2027
Code Description
P10 Set or clear departmental counter
P11 Display individual departmental counts
P13 Clear departmental counters
P14 Enter, clear or change department numbers
P16 Change max. number of copies that can be run
P18 Sends alarm if the wrong department number is tried three times in a row
P19 Change code number
P20 Adjust auto exposure
P21 Adjust automautic shufoff
P22 Adjust manual exposure
P23 Adjust auto clear time
P24 Set up fixed magnification settings
P25 Set maximum number of copies or of sets
P26 Binding margin
P27 Border erase setting
P28 Defaults at power on
P29 Display various counts
P30 Auto repeat on or off
P45 Message display time
P70 Auto paper select on or off
P71 Auto cassette select on or off
P72 Maximum copies in duplex
P73 Copy condition in rewrite
P74 Duplex limit when problems with duplex unit
P75 Prevent auto duplex
P76 Prevent stapling
P77 Prevent cover use
P90 List programs
Коды ошибок копировальных аппаратов

Sharp 2030
Code Description
C2 Transfer corona problem or HVT
CC Original detection problem.
CH Door open or developer unit not installed, not connected properly, or not latched in place properly.
Sub code 00: Communication error between main board and sorter. 01: Jogger error. 02: Sorter
F1
transport motor drive. 04: Sorter bin sensor problem. Lower limit sensed wrong.
Sub code 02: Toner motor problem. 31: Image density sensor problem. Could be a problem with the
F2 light level. 32: Drum mark sensor problem. Does not see mark on drum or sensor does not work
properly. 35: Grid voltage correction will not work during simulation.
F3 Sub code 12: Copier upper cassette lift motor problem. Copier bottom cassette lift motor problem.
H2 Fuser thermistor open.
H3 Fuser temperature too high.
H4 Fuser temperature too low. Lamp, thermal switch, connections.
L4 Sub code 01: Drive problem, main motor, sensor, bind.
L5 Sub code 03: Drive problem with 4th/5th mirror assembly, motor, sensor, board.
L8 Sub code 01: Power frequency problem.
PC Card counter or key counter not installed.
PF There is an inhibit command from the PC modem. This is reset with simulation 17.
U2 Sub code 00 or 01: Memory error.
U3 Sub code 20: Mirror motor locked. 21: Mirror motor home sensor.
U4 Sub code 02: Duplex alignment plate out of position motor, cable, sensor.
Sub code 00: Communication problem between main board and RADF. 01: RADF motor drive
U5
problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor.
Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive
U6
problem. 08: Desk 24v problem. 09: LCT motor overload. 10: Desk transport motor drive problem.
U7 Sub code 00: Communication problem between copier and PC modem.
Коды ошибок копировальных аппаратов

Sharp 2035
Code Description
P10 Set or clear departmental counter
P11 Display individual departmental counts
P13 Clear departmental counters
P14 Enter, clear or change department numbers
P16 Change max. number of copies that can be run
P18 Sends alarm if the wrong department number is tried three times in a row
P19 Change code number
P20 Adjust auto exposure
P21 Adjust automautic shufoff
P22 Adjust manual exposure
P23 Adjust auto clear time
P24 Set up fixed magnification settings
P25 Set maximum number of copies or of sets
P26 Binding margin
P27 Border erase setting
P28 Defaults at power on
P29 Display various counts
P30 Auto repeat on or off
P45 Message display time
P70 Auto paper select on or off
P71 Auto cassette select on or off
P72 Maximum copies in duplex
P73 Copy condition in rewrite
P74 Duplex limit when problems with duplex unit
P75 Prevent auto duplex
P76 Prevent stapling
P77 Prevent cover use
P90 List programs
Коды ошибок копировальных аппаратов

Sharp 2040
Code Description
C2 Transfer corona problem or HVT
CC Original detection problem.
CH Door open or developer unit not installed, not connected properly, or not latched in place properly.
H2 Fuser thermistor open.
H3 Fuser temperature too high.
H4 Fuser temperature too low. Lamp, thermal switch, connections.
L4 Sub code 01: Drive problem, main motor, sensor, bind.
L5 Sub code 03: Drive problem with 4th/5th mirror assembly, motor, sensor, board.
L8 Sub code 01: Power frequency problem.
PC Card counter or key counter not installed.
PF There is an inhibit command from the PC modem. This is reset with simulation 17.
U2 Sub code 00 or 01: Memory error.
U3 Sub code 20: Mirror motor locked. 21: Mirror motor home sensor.
U4 Sub code 02: Duplex alignment plate out of position motor, cable, sensor.
Sub code 00: Communication problem between main board and RADF. 01: RADF motor drive
U5
problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor.
Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive
U6
problem. 08: Desk 24v problem. 09: LCT motor overload. 10: Desk transport motor drive problem.
U7 Sub code 00: Communication problem between copier and PC modem.
Коды ошибок копировальных аппаратов

Sharp 2050
Code Description
CC-nn Original sensing problem
CH Lit steadily: Door open
CH Flashing: Developer unit not installed, not latched or not installed properly
EE-EL During developer calibration, overtoned condition detected
EE-EU During developer calibration, undertoned condition detected
F1-00 Communication problem between main board and stapler
F1-02 Stapler sorter transport drive problem
F1-03 Problem with guide bar oscillator motor
F1-04 Index lower sensor
F1-05 Index upper sensor
F1-06 Shift motor problem in stapler sorter, or index motor problem
F1-08 Staple sorter shift motor drive problem
F1-10 Stapler problem
F2-00 Toner sensor problem
F2-31 Drum surface reflecting problem
F2-32 Drum sensor not scanning mark properly
F2-33 Grid voltage is too high or too low
F2-35 During patch detection, measurement is wrong
F2-37 Drum mark sensor adjustment problem
F3-01 LCT encoder
F3-02 LCT lift problem
F3-03 LCT down problem
F3-12 Cassette 1 lift problem
F3-22 Cassette 2 lift problem
F3-32 Cassette 3 lift problem
F3-42 Cassette 4 lift problem
H2-00 Fuser thermistor
H3-00 Fuser temperature too high
H4-00 Fuser temperature too low
L1-00 Scan problem
L2-00 Mirror motor drive problem
L3-00 Scan return problem
L4-01 Drum motor drive problem
L4-02 Main motor drive problem
L5-00 4/5 mirror drive problem
L8-01 Full wave signal missing to auto exposure
L8-02 Full wave signal to auto exposure is incorrect
L8-03 During auto exposure adjust procedure, the auto exp.
P20 Adjust automatic exposure
P21 Auto shut off timing
P22 Toner save mode
P25 Maximum number of copies that can be selected
P26 Margin shift
P28 Initial status
P29 To read total copies
P70 Auto paper select
P72 Bypass in duplex
P74 Stop document feeder use
P75 Stop duplex use
P76 Stop stapler use
P83 Modem access to codes through phone line
P90 Display all of the operator programs
PC Card counter
PF Modem problem
U0-00 Operation panel problem
U2-00 EEPROM error. Reset with sim. 16
U3-00 Communication problem between master and mirror controller
U3-20 Mirror drive problem
U3-21 Mirror home sensor problem
U3-26 Mirror motor voltage problem
U3-41 Lens motor home correction did not go well
U3-42 4/5 mirror motor problem similar to U3 -41
U4-02 Duplex alignment plate sensor
U4-03 Duplex rear plate sensor
U5-00 Communication problem between RADF and copier
U5-01 RADF resist sensor
U5-02 RADF reverse sensor
U5-03 RADF timing sensor
U5-04 RADF empty sensor
U5-11 RADF paper feed drive problem
U5-12 RADF transport drive problem
U7-00 Communication problem between copier and modem
Коды ошибок копировальных аппаратов

Sharp 2114
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp 2116
Code Description
CH Flashing: DV unit not installed, not connected properly
CH Lit steadily: Sorter not installed or not turned on
EE-EL During developer calibration, problem of some kind. Over toned
EE-EU During developer calibration, problem of some kind. Under toned
F1-00 Communication error between main board and sorter
F1-02 Transport motor drive
F1-04 Bin sensor problem. Upper or lower limit sensor problem
F1-05 Sorter bin home sensor
F1-06 Sorter bin motor drive
F1-14 Take out sensor problem
F2-31 Image density sensor problem
F2-32 Drum mark sensor problem
F2-35 Grid voltage correction will not work on the patch voltage is outside the expected range
H2-00 Fuser thermistor open
H3-00 Fuser temperature too high
H4-00 Fuser temperature too low. Lamp, thermal switch, connections
L1 Scan forward problem
L3 Scan return problem
L4 Drive problem; main motor, gear, sensor, bind
L5 Lens problem
L8-01 Zero cross (board problem)
L8-03 Auto exposure sensor problem
P Paper feed problem
PC Card counter not installed
U2-01 Memory loss
U2-04 EEPROM error
U5-00 Communication problem between main board and ADF
U5-01 Registration sensor problem during adjustment, or adjustment value is not a valid number
U5-02 Exit sensor adjustment problem; invalid adjustment value
U5-11 Paper feed drive problem
U5-12 Transport motor drive
Коды ошибок копировальных аппаратов

Sharp 2118
Code Description
CH Flashing: DV unit not installed, not connected properly
CH Lit steadily: Sorter not installed or not turned on
EE-EL During developer calibration, problem of some kind. Over toned
EE-EU During developer calibration, problem of some kind. Under toned
F1-00 Communication error between main board and sorter
F1-02 Transport motor drive
F1-04 Bin sensor problem. Upper or lower limit sensor problem
F1-05 Sorter bin home sensor
F1-06 Sorter bin motor drive
F1-14 Take out sensor problem
F2-31 Image density sensor problem
F2-32 Drum mark sensor problem
F2-35 Grid voltage correction will not work on the patch voltage is outside the expected range
H2-00 Fuser thermistor open
H3-00 Fuser temperature too high
H4-00 Fuser temperature too low. Lamp, thermal switch, connections
L1 Scan forward problem
L3 Scan return problem
L4 Drive problem; main motor, gear, sensor, bind
L5 Lens problem
L8-01 Zero cross (board problem)
L8-03 Auto exposure sensor problem
P Paper feed problem
PC Card counter not installed
U2-01 Memory loss
U2-04 EEPROM error
U5-00 Communication problem between main board and ADF
U5-01 Registration sensor problem during adjustment, or adjustment value is not a valid number
U5-02 Exit sensor adjustment problem; invalid adjustment value
U5-11 Paper feed drive problem
U5-12 Transport motor drive
Коды ошибок копировальных аппаратов

Sharp 2120
Code Description
CC Original detection problem
CH Lit Steadily: Sorter not installed, or not turned on
CH Flashing: DV unit not installed, not connected properly, or not latched in place properly
Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport
F1
motor drive.
Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark
F2
sensor problem. . Does not see mark on drum or sensor not working properly.
H2 Sub code 00: Fuser thermistor open.
H3 Sub code 00: Fuser temperature too high.
H4 Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.
L1 Scan forward problem. Motor, sensor, board
L3 Scan forward problem. Motor, sensor, board.
L4 Drive problem; main motor, gear, sensor, bind.
L5 Lens problem. Motor sensor board.
L8 Sub code 01: Zero cross.
P Paper feed problem or no paper
PC Card counter not installed
U2 Sub code 01: Memory loss.
U4 Sub code 00: Communication problem between copier and duplex unit.
U5 Sub code 00: Communication problem between main board and ADF.
Коды ошибок копировальных аппаратов

Sharp 2214
Code Description
A1 Jam in document feeder
A2 Jam in document feeder
C1 Cassette misfeed
C2 Cassette feed, bypass unplugged
C3 Bypass misfeed
E1 Paper feed jam
E3 Exit jam
EE-EL Developer overtoned during setup
EE-EU Developer undertoned during setup
J0 Developer setup taking place
J1 Add toner
J3 Drum unit not installed properly or missing
J7 Drum unit due for replacing
J8 Wrong drum unit or power was turned on after J7 displayed
L6 Key counter or other optional counter accessory problem
U1 Drive problem
U2 Scan
U3 Lens
U4-01 Fuser thermistor
U4-02 High fuser temperature
U4-03 Low fuser temperature
U5 500 sheet cassette lift motor
U6 Main board problem
U7 Document glass too hot (with document feeder)
U8 Problem with line voltage
U9 Auto developer setup problem
Коды ошибок копировальных аппаратов

Sharp 2216
Code Description
CC Original detection problem
CH Lit Steadily: Sorter not installed, or not turned on
CH Flashing: DV unit not installed, not connected properly, or not latched in place properly
Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport
F1
motor drive.
Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark
F2
sensor problem. . Does not see mark on drum or sensor not working properly.
H2 Sub code 00: Fuser thermistor open.
H3 Sub code 00: Fuser temperature too high.
H4 Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.
L1 Scan forward problem. Motor, sensor, board
L3 Scan forward problem. Motor, sensor, board.
L4 Drive problem; main motor, gear, sensor, bind.
L5 Lens problem. Motor sensor board.
L8 Sub code 01: Zero cross.
P Paper feed problem or no paper
PC Card counter not installed
U2 Sub code 01: Memory loss.
U4 Sub code 00: Communication problem between copier and duplex unit.
U5 Sub code 00: Communication problem between main board and ADF.
Коды ошибок копировальных аппаратов

Sharp 2414
Code Description
If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing,
CH
developer seal still installed, or toner density sensor/main board problem.
Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub
EE
code EL: Over toned. May be toner density sensor problem or developer unit problem.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L1 leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came
off.
L3 Scan return problem. Sub code 0. Approximately same causes as L1
L4 Sub code 1: Main drive problem. Sensor, gear, motor.
L5 Sub code 2: Lens drive, motor, sensor.
Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE
L8
sensor problem.
PC Key counter not installed.
SPFJAM Document feeder problem.
U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.
U5 Sub code 5: high temperature at exposure glass when using document feeder.
Коды ошибок копировальных аппаратов

Sharp 2514
Code Description
If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing,
CH
developer seal still installed, or toner density sensor/main board problem.
Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub
EE
code EL: Over toned. May be toner density sensor problem or developer unit problem.
H2 Sub code 0: Fuser thermistor.
H3 Sub code 0: Fuser temperature too high.
H4 Sub code 0: Fuser temperature too low.
Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not
L1 leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came
off.
L3 Scan return problem. Sub code 0. Approximately same causes as L1
L4 Sub code 1: Main drive problem. Sensor, gear, motor.
L5 Sub code 2: Lens drive, motor, sensor.
Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE
L8
sensor problem.
PC Key counter not installed.
SPFJAM Document feeder problem.
U2 Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.
U5 Sub code 5: high temperature at exposure glass when using document feeder.
Коды ошибок копировальных аппаратов

Sharp 7100
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 7200
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 7320
Code Description
CH Door open or developer unit out
EL Developer problem
EU Developer set up problem
P
Out of paper
flashing
P lit No cassette in machine
PC Personal counter not installed
U3 Auto exposure sensor problem
Коды ошибок копировальных аппаратов

Sharp 7370
Code Description
CH Door open or developer unit out
EL Developer problem
EU Developer set up problem
P
Out of paper
flashing
P lit No cassette in machine
PC Personal counter not installed
Коды ошибок копировальных аппаратов

Sharp 750
Code Description SERVICE TIPS & PROCEDURES
0 Stepping motor Maintenance Counter reset is CROP 20, Print
Contributed by: Steve
10 Mirror motor
General reset for error codes is CROP 14 Print
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 755
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 756
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 760
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
L6 Charge block switch
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 770
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
0 Main board, operations panel
0 Data transfer (main and operations)
0 Data transfer (main and ADF)
1 Document feeded motors
1 Exposure lamp board or operations
2 Automatic exposure sensor, exposure lamp board
U Press {Print} and read secondary code:
U3 Press {Print} and read secondary code:
U4 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 7700
Code Description
0 Data transfer (main and ADF)
0 Data transfer (main and operations)
0 Main board, operations panel
1 Document feeded motors
1 Exposure lamp board or operations
2 Automatic exposure sensor, exposure lamp board
U Press {Print} and read secondary code:
U3 Press {Print} and read secondary code:
U4 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 771
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH possible DV unit not installed properly
CH Interlock or thermal fuse
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
Коды ошибок копировальных аппаратов

Sharp 7750
Code Description
0 Data transfer (main and ADF)
0 Data transfer (main and operations)
0 Main board, operations panel
1 Document feeded motors
1 Exposure lamp board or operations
2 Automatic exposure sensor, exposure lamp board
U Press {Print} and read secondary code:
U3 Press {Print} and read secondary code:
U4 Press {Print} and read secondary code:
Коды ошибок копировальных аппаратов

Sharp 780
Code Description
0 Stepping motor
10 Mirror motor
40 Dark box switch
8 Mirror motor
C1 Charge corona
C2 Transfer corona
C3 Discharge corona
CH Interlock or thermal fuse
CH possible DV unit not installed properly
H1 Heater thermal fuse
H2 Thermistor
H3 High Temperature
H4 Low Temperature
H5 Lower thermofuse
H6 Lower thermistor
H7 High temperature in lower roller
H8 Low temperature in lower roller
L1 Forward Scan
L2 End of Scan
L3 Return of Scan
L4 PT/main motor
L5 Lens
P1 Copy lamp thermal fuse
U1 Low battery
U2 Data transfer
U3 Dark box
CC Document sensor
CH Door open
EE Developer did not set up properly
EL Developer sensor
EU Developer sensor
H2 Thermistor
H3 High temperature
H4 Low temperature
L1 Forward scan
L2 Forward scan
L3 Scan return
L5 Lens
L6 Bottom rotating cassette
L8 Signal
L9 Sorter
U1 Battery
U2 Back up battery
U3 Auto exposure sensor
U5 Problem in interface between machine and ADF
Коды ошибок копировальных аппаратов

Sharp 7800
Code Description

<<

стр. 9
(всего 13)

СОДЕРЖАНИЕ

>>